FENGYUN ELE B0BXWD14VQ 48 Ceiling Fans with Light User Manual

FENGYUN ELE B0BXWD14VQ 48 Ceiling Fans with Light User Manual

Safety information

1. L. To avoid electric shock or fire tasand, do not apply a voltage or power outside the range specified of the product.
2. To reduce the risk of electrical shock, the electricity supplied to the ceiling FAN must be cat off before installation
3. All wiring must be in accordance with the Sational and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
4. To reduce the risk of electric shock, this fan aust be installed with an isolating wall control/avitch
5. No matter the ceiling is made of wood or concrets, the ceiling must support at least 351ha (15.9kg). Otherwise, the fan sould drop dom
6. Do not insert foreign objects in between rotating fan blades.
7. A minimum height of 7.3 ft. (2.3m) between the fan blades and floor must be kept, otherwise it may cause Injury.
8. omical barn Barand. Keep batteries away from children. This remote contains a lithium iitton rell battery. If a new or used lithim button/coin cell hattery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely close the battery coquartaent. If the battery conquartaent does not clase securely, stop using the pendact remove the hatteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek imediate medical attention. Dispose of cells properly and keep them away from children. Even used cells may cause injury.

Product Specification

Ceiling Fan Size: 48

Material : Silicon Steel/Copper/Plastic Blade

Light Cover Material: Acrylic

Light Kit: Led Double Color 18

Control Mode: Remote Control

Motor: 100% Copper Motor

Voltage: 120v 60hz or 220v 50hz

Checking material

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size

PACKAGE CONTENTS

Installation of the hanging bracket

1. Switch off the electrical mains breaker.
2. Screw up four self-tapping screws with electric automation driller on the wood ceiling to fix the mounting bracket as shown in the picture above (Expansion screw for concrete ceiling).

Important notice:
No matter the ceiling is made of wood or concrete, the ceiling must support at least 35 lbs (16kg). Otherwise, the fan would drop down.

Installation the hanging part of ceiling fan

Install downrod assembly

1. Remove the ‘R’ pin and cross pin from the down rod.

2. Install the canopy and coupling cover through the down rod.
   

3. Thread the wires through the downrod, insert the downrod into the coupler and loosen the two screws on the coupler.

4. Install back the cross pin and secure with the ‘R’ pin, the ‘R’ pin must be properly installed to prevent the cross pin from working loose.
   

5. Tighten the two screws on the coupler.
   

Hanging the fan.

Carefully lift the fan and assembly into mountain bracket which is attached to the outlet hox. Ensure the rod hall’s groove is lined up with tab on the hanger bracket.

Wiring of the Ceiling fan

1. Making the electrical connections

WARNING The ceiling fan must be grounded. If the pround wire for the installation site is not present, Immediately STOP Installation and consult a quallified electrician.

1. As shown in the picture above, install the four wires from the fanbody into the remote control receiver. The vires corresponding ones are: Light L(white) Vire(black), Neutral N(blue) cannot be mixed by color. The Rever Function (brown), Fan Live
2. Secondly, connect the L and N vires of power supply to the connector of the remote control receiver: White to L, Blue to N. Thirdly, connect the grond vires of the power supply to the grond wire (the green wire) of the hanger: Green to.

Install the canopy

1. After wiring is done, put the remote control receiver in the mounting bracket.

2. Carefully push the canopy to the bottom of the mounting bracket, and then screw up the two screws clockwise.

Attaching the fan blades

Install two screws for each blade, one by one, until Three of blades have been installed (the screws can be found in the hardware hag.)

Assembly-attaching the lights

CAUTION: To reduce the risk of electric shock, make sure the electricity is off before installation.

1. Connecting the wires between fan-motor body and light kit fitter assembly (white wire to white, blue to blue).
   

2. Tighten the three screws of the lower cover.

3. Screw the lamp cover into the lower cover.

Operation

OPERATING YOUR FAN
Power on the electricity, turn on the led lights and start fan running by remote controller.

Note: if you have trouble installing, please scan the QR code and watch the product installation video in.

Use of remote control

1. Switch
2. Fan off 21
3. Speed of fan
4. Reverse Function
5. ON/OFF the Light
6. Timing contrel

with battery

Note:

Reverse function:
Two modes (downdraft and updraft) former and winter. To change the direction of air flos, preas the reverse function to opposite position.
Downdraft mode make you feeling cool in sщит.
Updraft mode keep the room warm by circulating the warm air in winter.

ON/OFF the light:
Three modes of light, to take care of your whole family.
White light:   CET 6000K
Neutral light:   CCT 4000
Ware light:   CET 3000K

Care and Cleaning

• WARNING: Make sure the power is off before cleaning your fan.

• Because of the fan’s natural movement, somme on nations may become loose. Check the import connections, brackets, and blade attachments twire a year. Make sure they are serare. It is not necessary to remove the fan from the eviling

• Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly ca electrical shock. Use only a soft brush or liat-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.

• You can apply a light noat of furniture polish to the wood for additional protection and
  enlanced beauty. Cover small scratches with a light application of shoe polish

• You do not need to oil your fan. The motor hum peramentir-lubricated sealed ball bearings.

Help

Thin naer minnal is designed to make installation as many as possible. Keep your кастрати по tablet nearby while reading this user manual. We have added a installation video to help you understand more of the installation technical code of the part. If you are unfamiliar or uncomfortable with wiring or repairs, contact a qualified electrician

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>