SCHONBEK BWSW32327-BK Beyond Glacier LED Outdoor Wall Light Instruction Manual

SCHONBEK BWSW32327-BK Beyond Glacier LED Outdoor Wall Light Instruction Manual

ASSEMBLY & INSTALLATION INSTRUCTIONS

PREPARATION

1.  Shutoff the power a the dircuit breaker and remove existing fiture, induding the crossbar.

2. Carefullyunpackyour new fixture and lay out althe parts on aclear area Be careful not to lose any small parts necessary for ingtalation.
   MOUNTING THE FIXTURE (Fig. 1)
   

3. Remove the mounting screw (B) and umber gasket(C)from the wall plate.

4. Removethe two screws F) and spring washers (G on the back plate which is unglued syce, loosen but donotremove the micklle two screws

5. Tumthe fixture bookly B outward urtilyou can putthe crystalinto the fixture body A and. Secure the back plate screws and spiing washers

6. Thefixture can switch between three color temperatures (000K 3500k-4000K), which can be adjustedito your preference with the swich in t the back plate **(Fig.5).

**

7. Diill holesin the wall ligned with the key holes located inthe wallplate. Insert the plastic anchors (D).
8. First, secure the wall plate tothe junction box using the original junction box screws. Second, fasten the wall plate tothe wal using plastic anchor (D) and ancher screw E).
   (i) It s recommendecito use only originaljunction box screws or replacements provided by junction box manufacturer.
   (i) The sice of the wallplate marked “GND” must face out, towards the installer
   CONNECTING THE WIRES (Fig. 2)
   Wiring

** Fixture Wires
Black or Smooth|
House Wires
Black
(Live)
---|---
Fixture Wires
White or Ribbed|
House Wires
White (Neutral)
Fixture Wires
Bare wire (Ground)| House Wires
Green or Bare Copper (Ground)
9. Connect the driver’s input wires to the junction box wires (Fig.2) using wire connectors A) provided Endure al wire connectors are secure. Connect th fuxture’s groundwire to the groundin the junction box; this willbe either a green wire or a bare copper wire. After uture is wired to house wires, tuckwires carefully insice the junction box.
DIMMING WIRING INFORMATION (Fig.3)
** Purple-Dim+ Pink or Gray-Dim- Red-To Fixture+
Black-To Fixture-

Purple-Dim+
Pink or Gray-Dim- Red-
To Fixture+
Black-To Fixture-

10. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for dimming wires information i) To utilize ELV or TRAIC dimming use wires back live), white (neutral) and house green wire or bare copper wire (ground) Don’t use dimmer wires on driver for ELV or TRAIC dimming (i) To utilize 0-10/ dimming use wires purple (cim+) Pink or gray (dim-)farm river and connect to corresponding wireline junction box.
    NOTE: Make sure to connect 0-10V price to power-up the fixture in order to allow the 0-10V coming to function properly.
    COMPLETING THEINSTALLATION

11. . Secure the fixture to the wall plate using the mounting serew (B) and rubber gasket(C, 12. To prevent moisture from entering the outlet box and causing a short, use dear caulking(i eindoor/outdoor silicone sealant) to outline the outside o ixture back plate where it meets the wall, Leave a space a the bottom to allow mositure to escape Fig .4
    MAINTENANCE NOTE: Coastal conditions may cause mineral andiresiduebuilchup on the fixture. We recommend that customers in coastal areas clean all extenal surfaces o the fiture once every twoweeks with a wet cloth.

MOUNTING BACK PLATE

HARDWARE

• Wire Connector Qy 3pes+ Extra

• Mounting Screw Q1 Batra

• Rubber Gasket Quibtra

• Anchor Qy2po+iEda

• Wood Screw Qi: 2pes+ 1Extra

• backplane Screw Q. 1Bxtra

• prang Washer Q182

ASSEMBLY & INSTALLATION INSTRUCTIONS

Fixture

Fig.1

PREPARATION

1. Shutoff the power a the circuit breaker and remove existing future, inducing the crossbar.

2. Carefully unpack your new fixture and lay out al the parts on clear area Be careful not to lose any small parts necessary for in gradation.
   MOUNTING THE FIXTURE (Fig. 1)

3. Remove the mounting screw (B) and umber gasket(C)from the wall plate.

4. Remove the two screws F) and spring washers (G on the back plate which is unglued syce, loosen but donotremove the mackle two screws

5. Tum the fixture bookly B outward urtilyou can puttee crystal into the fixture body A and lB. Secure the back plate screws and spying washers [~ ‘when the Aysal s fasten between tween to future bodies.

6. The fixture can switch between three color temperatures (000K 3500k-4000K), which can be adjusted ditto your preference with the swish in the back plate (Fig.5).

7. Dill holes the wall ligned with the key holes located in the wall plate. Insert the plastic anchors (D).

8. First, secure the wall plate to the junction box using the original junction box screws. Second, fasten the wall plate to the wall using plastic anchor (D) and anther screw E).
   (i) It s recommendecito use only original junction box screws or replacements provided by junction box manufacturer.
   (i ) The syce of the wall plate marked “GND” must face out, towards the installer
   CONNECTING THE WIRES (Fig. 2)

9. Connect the driver’s input wires to the junction box wires (Fig.2) using wire connectors A) provided Endure al wire connectors are secure. Connect the fixture’s groundfire to the grounding the junction box; this will be either a green wire or a bare copper wire. After future is wired to house wires, tuck wires carefully inside the junction box.
   DIMMING WIRING INFORMATION (Fig.3)

10. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for dimming wires information.
    ( 1 ) To utilize ELV or TRAIC dimming: use wires black (live), white (neutral) and house green wire or bare copper wire (ground). Do not use dimmer wires on driver for ELV or TRAIC dimming.
    (i) To utilize 0-10V dimming: use wires purple (dim+), Pink or gray (dim-) from driver and connect to corresponding wires in junction box.
    NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
    COMPLETING THE INSTALLATION

11. Secure the fixture to the wall plate using the mounting screw (B) and rubber gasket(Q)

12. To prevent moisture from entering the outlet box and causing a short, use dear caulking(ive indoor/outdoor silicone sealant) to out linethe outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig.4.
    MAINTENANCE NOTE : Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>