SCHONBEK BPD46237-AB Beyond Benediction LED Chandelier Ceiling Light Instruction Manual
- October 30, 2023
- SCHONBEK
Table of Contents
SCHONBEK BPD46237-AB Beyond Benediction LED Chandelier Ceiling Light
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation in accordance with the National Electrical Code (NEC), other applicable installation code(s) and local regulations by a licensed electrician familiar with the operation of the product and the hazards involved.
- Go to the main fuse box, or circuit breaker panel. Place the main power switch in the “OFF” position and unscrew the fuse (s) or switch ”OFF” the circuit breaker switch (es) that control the power to the fixture (s) or room that you are working on.
- Place the wall switch in the “OFF” position.
- FAILURE TO INSTALL THIS FIXTURE IN ACCORDANCE WITH THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND/OR PROPERTY DAMAGE.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL Listing of this fixture.
- When handling the fixture, do not apply pressure to the LEDs or bulbs. Hold the fixture by the base only.
- Do not exceed maximum wattage noted on the fixture. Use only the recommended LED or standard lamps with the fixture.
PREPARATION
-
Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
-
Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE AND Crystal (Fig. 1and Fig.2) -
Remove the mounting screw (B) from the fixture.
-
The lamp can switch between three color temperatures (3000k-3500k-4000k), which can be adjusted to your preference with the switch in the canopy (Fig.4).
-
Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (D).
-
Secure the mounting plate to the junction box using junction box screws. fasten it to the wall using wood screws (C).
Note: (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue; (ii) The side of the mounting plate marked “GND” must face out. -
Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
-
Retract these wires close to a desirable length to within the canopy before securing the fixture in place.
Note: retracting or extending excessive cable length through the cable gripper is not recommended. -
Warning: Shortening these cables without professional helps or electronic background is not advisable. Any modifications to the fixture may result in voiding the warranty of the product(Fig.5).
CONNECTING THE WIRES (Fig. 3) -
Hook the safety cords to the mounting plate.
-
Connect the driver input/output wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare c opper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate usingthe screw provided. After wires are connected, tuck them carefully inside the junction box.
-
Hold the canopy in both hands and put it on the mounting ring as shown in the fig 1,then rotate in the direction of the arrow until it can’t move. secure it with back plate screw(B).
-
Turn on the power to test the lamp.
INSTALL DECORATIVE CRYSTAL (Fig. 2) -
Before installing the crystal, adjust the cable length again to ensure that the lamp body remains level and the wire is not load-bearing.
-
Insert the crystal assembly obliquely into the lamp body slot, and then fix the cover plate with assembly screws(E).
Note: (i)Pay attention to orientation when assembling crystals. (ii)When assembling the crystal, the lamp body should be balanced and the last part of the crystal should be assembled into the lamp body near the wire.
NOTE: DIMMING WIRING INFORMATION (Fig. 5)
- This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires information.
- To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
- To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
HARDWARE
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901
Phone: 1-800-836-1892 | Fax: 518-563-4228 |
www.schonbek.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>