SCHONBEK BPD74232 Pendant LED Fixture Instruction Manual

: October 30, 2023
: SCHONBEK

Table of Contents

SCHONBEK BPD74232 Pendant LED Fixture
OVERVIEW
PREPARATION
HARDWARE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SCHONBEK BPD74232 Pendant LED Fixture

OVERVIEW

SCHONBEK-BPD74232-Pendant-LED-Fixture-fig-6

WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.

Read all instructions before installing.
The system is intended for installation in accordance with the National Electrical Code (NEC), other applicable installation code(s), and local regulations by a licensed electrician familiar with the operation of the product and the hazards involved.
Go to the main fuse box or circuit breaker panel. Place the main power switch in the “OFF” position and unscrew the fuse (s) or switch ”OFF” the circuit breaker switch (es) that controls the power to the fixture (s) or room that you are working on.
Place the wall switch in the “OFF” position.
FAILURE TO INSTALL THIS FIXTURE IN ACCORDANCE WITH THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND/OR PROPERTY DAMAGE.

CAUTION

All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL Listing of this fixture.
When handling the fixture, do not apply pressure to the LEDs or bulbs. Hold the fixture by the base only.
Do not exceed the maximum wattage noted on the fixture. Use only the recommended LED or standard lamps with the fixture.

PREPARATION

Shut off the power at the circuit breaker and remove the existing fixture, including the crossbar.
Carefully unpack your new fixture and lay out all the parts in a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE Crystal AND FIXTURE
Install from the inside, the Cloud crystal against the spring sheet, and press hard, and the two convex points of the crystal are aligned with the two holes of the fixture so that the spring can automatically return.
Remove the mounting screw (B) from the fixture.
The lamp can switch between three color temperatures (3000k-3500k-4000k), which can be adjusted to your preference with the switch in the canopy (Fig.4).
Drill holes in the wall aligned with the keyholes located in the mounting back plate, insert the plastic anchor (D).
Secure the mounting plate to the junction box using junction box screws. fasten it to the wall using wood screws (C).
Note:
- (i) Using any other non-original-manufacturer-provided junction box screw may result in safety issues;
- (in) The side of the mounting plate marked “GND” must face out.
Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
- a. Retract these wires close to a desirable length within the canopy before securing the fixture in place. Note: retracting or extending excessive cable length through the cable gripper is not recommended.
- b. Warning: Shortening these cables without professional help or electronic background is not advisable. Any modifications to the fixture may result in voiding the warranty of the product.
  CONNECTING THE WIRES
Hook the safety cords to the mounting plate.
Connect the driver input/output wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the screw provided. After the wires are connected, tuck them carefully inside the junction box.
Secure the fixture by mounting the canopy to the ring of the backplate. Turn and rotate the canopy until it stops. Fasten the canopy to the back plate using the mounting screw (B).
NOTE: DIMMING WIRING INFORMATION
This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires information.
To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).