ENFORCER SD-9263-KSVQ Outdoor Wave Open Sensors Instruction Manual

: June 13, 2024
: ENFORCER

Table of Contents

ENFORCER SD-9263-KSVQ Outdoor Wave Open Sensors
Product Information: Outdoor Wave-to-Open Sensors
Specifications
Overview
Troubleshooting
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ENFORCER SD-9263-KSVQ Outdoor Wave Open Sensors

ENFORCER-SD-9263-KSVQ-Outdoor-Wave-Open-Sensors-
product

Product Information: Outdoor Wave-to-Open Sensors

The Outdoor Wave-to-Open Sensor is a full-featured exit plate that utilizes IR technology to allow egress from a protected area or activate a device with a simple wave of a hand. This sensor is suitable for use in hospitals, clinics, labs, cleanrooms, schools, factories, or offices. It features adjustable sensor range, a relay with adjustable trigger duration, LED illuminated sensor for easy identification, selectable LED colors, stainless steel plate, and IP65 weather resistance for outdoor use.

Key Features

Adjustable sensor range up to 7″ (18cm)
1.2A relay with adjustable trigger duration of 0.5~30 seconds or toggle
LED illuminated sensor for easy identification
Selectable LED colors that turn from red to green (or green to red) when the sensor is activated
Stainless steel plate
IP65 weather-resistant for outdoor use
Power must be provided by low-voltage power-limited/Class 2 power supply
Use only low-voltage field wiring and do not exceed 98.5 ft (30m)

Specifications

Model| Operating Voltage| Relay Type| Response Time| LEDs| Output Duration| Range| IP Rating| Operating Temperature| Weight
---|---|---|---|---|---|---|---|---|---
Slimline| 12~24 VDC| SPDT dry contact, 1.2A@24VDC| 10ms| Red / Green| 0.5~30 s, toggle| 2~7″ (5~18 cm)| Weatherproof, IP65| –| 2.2-oz (61g) / 2.7-oz (77g)
Single-Gang European Plate| 12~24 VDC| SPDT dry contact, 1.2A@24VDC| 10ms| Red / Green| 0.5~30 s, toggle| 2~7″ (5~18 cm)| Weatherproof, IP65| –| 3.8-oz (108g)
Double-Gang| –| –| –| –| –| –| –| –| 5.6-oz (160g)

Installation Notes

This product must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electrical Code CSA C22.1.
Due to the nature of IR technology, an IR sensor can be triggered by a direct light source such as sunlight, reflected light from a shiny object, or other direct light. Therefore, in some locations, it may be necessary to install a hood or other barrier to shield the sensor from direct light sources.

Language| Slimline| Single- Gang| **European Plate*| Double- Gang**
---|---|---|---|---
English| SD-9163-KSQ| SD-9263-KSQ| SD-9363-KSQ|
Spanish| SD-9163-KS1Q| SD-9263-KS1Q| SD-9363-KS1Q|
French| SD-9163-KS2Q| SD-9263-KS2Q| SD-9363-KS2Q|
English

w/ mechanical override button

| SD-9163-KSVQ| SD-9263-KSVQ| SD-9363-KSVQ†| SD-9463-KSVQ†

The ENFORCER Outdoor Wave-to-Open Sensor is a full-featured exit plate using IR technology to allow egress from a protected area or activate a device with the simple wave of a hand. Since no touch is required, this sensor is suitable for use in hospitals, clinics, labs, cleanrooms (to reduce the risk of contamination), schools, factories, or offices.

Adjustable sensor range up to 7″ (18cm)
1.2A relay, adjustable trigger duration 0.5~30 seconds or toggle
LED illuminated sensor are for easy identification
Selectable LED colors turns from red to green (or green to red) when the sensor is activated
Stainless steel plate
IP65 Weather-resistant for outdoor use
Power must be provided by low-voltage power-limited/Class 2 power supply
Use only low-voltage field wiring and do not exceed 98.5 ft (30m)

Parts List

1x Wave-to-Open Sensor
2x Faceplate screws
1x Wiring harness

1x Manual

Specifications

Model| Slimline| Single- gang| European plate| Double- gang
---|---|---|---|---
Operating voltage| 12~24 VDC
Current draw (max.

±10%)

Overview

Sensor layout (except slimline, single-gang shown)

$ENFORCER-SD-9263-KSVQ Outdoor-Wave Open-Sensors $1$$ Other Faceplate Dimensions

European Plate
33/8″x33/8″ (86×86 mm) Double-Gang
41/2″x49/16″ (116×115 mm)

INSTALLATION NOTES

This product must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electrical Code CSA C22.1.
Due to the nature of IR technology, an IR sensor can be triggered by a direct light source such as sunlight, reflected light from a shiny object, or other direct light. Therefore, in some locations it may be necessary to install a hood or other barrier to shield the sensor from direct light sources.

Wiring Diagram

Wiring for Wave-to-Open Sensor
with Form C Mechanical Override Button (SD-9263-KSVQ shown) $ENFORCER- SD-9263-KSVQ Outdoor-Wave Open-Sensors $2$$

Installation

Run four wires through the wall to a corresponding back box. Power must be provided by a low-voltage power-limited/Class 2 power supply and low-voltage field wiring not to exceed 98.5ft (30m).
Connect the 4 wires from the back box to the sensor according to the Wiring Diagram above.
For weatherproof installation, use a waterproof back box and apply a bead of silicone sealant (not included) around the rim of the back box and faceplate edge. Apply a small amount of sealant below each screw head.
Screw the plate into the back box, taking care not to crimp the wires and ensuring a good seal.
Remove clear protective film from the sensor before use.

WARNING: Do not connect any device that will exceed 1.2A@24VDC.

Changing the LED Color Slimline Models

$ENFORCER-SD-9263-KSVQ Outdoor-Wave Open-Sensors $3$$

Adjusting the Sensor Range and Output Duration

The sensor range can be adjusted from 2″~7″ (5~18 cm).
Output duration can be adjusted from 0.5~30 seconds or toggle.*

NOTE: Do not force the adjustment trimpots to turn. Only minimal force is needed

*Output duration: 0.5~30 seconds, toggle Default* : 0.5 seconds
Toggle: turn clockwise to maximum position

Sensor range: 2″~7″ (5~18 cm) Default: 7″ (18cm)

Sample Installation

$ENFORCER-SD-9263-KSVQ Outdoor-Wave Open-Sensors $7$$

Override button is pre-wired at the factory. No further wiring is necessary.

Troubleshooting

Sensor triggers
unexpectedly
Ensure that no strong direct or reflected light source is reaching the sensor.
Ensure that sensor is sheltered from direct sunlight.
Sensor remains triggered
Check that nothing is remaining in range of the sensor including a cone of 60º from the centerline.
Reduce the IR range of the sensor.
Ensure that the sensor’s output duration potentiometer is not turned to maximum
Check that the power voltage is within the sensor’s specifications.
Sensor will not
trigger
Increase the IR range of the sensor.
Check that the power voltage is within the sensor’s specifications.

Care and Cleaning
The sensor requires special care to ensure reliability and a long operating life.

Use a soft, clean, preferably microfiber cloth for cleaning. Use the mildest type of cleaner available.
When cleaning, spray the cleaning solution onto the cleaning cloth instead of the unit.
Be sure to wipe off any excess liquid from the sensor. Wet spots may affect the sensor’s performance.

IMPORTANT WARNING: For a weather-resistant installation, ensure that the unit is installed in a waterproof back box, and that the faceplate and faceplate screws are properly sealed. Incorrect mounting may lead to exposure to rain or moisture inside which could cause a dangerous electric shock, damage the device, and void the warranty. Users and installers are responsible for ensuring that this product is properly installed and sealed.

IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

California Proposition 65 Warning : These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022 SECO-LARM U.S.A., Inc. All rights reserved.

SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606