ADJ MDF2PSUX20 Power Supply User Manual
- June 5, 2024
- ADJ
Table of Contents
MDF2PSUX20
Safety Manual
GENERAL
INTRODUCTION
This fixture has been designed to perform reliably for years when the
information in this manual are followed. Please read and understand all the
instructions and guidelines carefully and thoroughly before operating this
unit. This manual contains important information regarding safety,
installation, use, and maintenance.
UNPACKING
Each fixture has been thoroughly tested and shipped in perfect operating
condition. Carefully check the outer shipping carton for signs of any damage
that may have occurred during shipping. If the outer carton appears to be
damaged, carefully inspect the fixture for damage and be sure all included
accessories have arrived intact. In the event damage has been found and/or
parts are missing, please contact our customer support team for further
instructions. Please do NOT return this fixture to your dealer without first
contacting customer support at the number listed below. Please do NOT discard
the outer shipping carton in the trash. Please recycle whenever possible.
INCLUDED ITEMS
Power Cable (x1)
CUSTOMER SUPPORT: Contact ADJ Service for any product-related service and
support needs. Also visit forums.adj.com with
questions, comments, or suggestions.
ADJ SERVICE USA – Monday – Friday 8:00am to 4:30pm PST
Voice:800-322-6337 | Fax:
323-582-2941 |
support@adj.com
ADJ SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96
|support@adj.eu
REPLACEMENT PARTS please visitparts.adj.com
WARRANTY RETURNS
All returned service items, whether under warranty or not, must be freight
pre-paid and accompanied by a return authorization (R.A.) number. The R.A.
number must be clearly written on the outside of the return package. A brief
description of the problem, as well as the R.A. number, must also be written
down on a piece of paper and included in the shipping container. If the unit
is under warranty, you must provide a copy of your proof of purchase invoice.
Items returned without an R.A. number clearly marked on the outside of the
package will be refused and returned at the customer’s expense. You may obtain
an R.A. number by contacting customer support.
LIMITED WARRANTY (USA ONLY)
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ
Products, LLC products to be free of manufacturing defects in material and
workmanship for a prescribed period from the date of purchase (see specific
warranty periods below). This warranty shall be valid only if the product is
purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place
of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number
(RA#) before sending back the product–please contact ADJ Products, LLC Service
Department at 800-322-6337. Send the
product only to the ADJ Products, LLC factory. All shipping charges must be
pre-paid. If the requested repairs or services (including parts replacement)
are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States.
If the entire instrument is sent, it must be shipped in its original package.
No accessories should be shipped with the product. If any accessories are
shipped with the product, ADJ Products, LLC shall have no liability whatsoever
for loss of or damage to any such accessories, or for the safe return thereof.
C. This warranty is void if the serial number has been altered or
removed; if the product is modified in any manner which ADJ Products, LLC
concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products,
LLC factory unless prior written authorization was issued to purchaser by ADJ
Products, LLC; if the product is damaged because not properly maintained as
set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include
maintenance, cleaning, or periodic checkup. During the period specified above,
ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship. The sole responsibility
of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or replacement thereof, including parts, at the sole discretion of
ADJ Products, LLC. All products covered by this warranty were manufactured
after August 15, 2012, and bear identifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or
improvements to its products without any obligation to include these changes
in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
LIMITED WARRANTY PERIODS
- Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc. excluding LED and lamps)
- Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty).
- LED Products = 2-Year (730 Days) (excluding batteries that have a 180-Day Limited Warranty)PLEASE NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to products purchased within the USA.
- StarTec Series = 1-Year (365 Days) (excluding batteries that have a 180 Day Limited Warranty)
- ADJ DMX Controllers = 2 Year (730 Days)
- American Audio Products = 1 Year (365 Days)
SAFETY GUIDELINES
This fixture is a sophisticated piece of electronic equipment. To guarantee
smooth operation, it is important to follow all instructions and guidelines in
this manual. ADJ is not responsible for injury and/ or damages resulting from
the misuse of this fixture due to the disregard of the information printed in
this manual. Only qualified and/or certified personnel should perform the
installation of this fixture and only the original rigging parts (omega
brackets) included with this fixture should be used for installation. Any
modifications to the fixture and/or the included mounting hardware will void
the original manufacturer’s warranty and increase the risk of damage and/or
personal injury.
IP RATING: This device is IP20 rated. This means that the unit is protected
against intrusion from solids approximately the size of an adult finger (12mm
in diameter) and that the unit is NOT protected against water intrusion of any
kind!
| PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
---|---
| THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY
REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
| DO NOT PLUG THE FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
DISCONNECT FIXTURE FROM POWER BEFORE SERVICING!
NEVER TOUCH THE FIXTURE DURING OPERATION, AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM THE FIXTURE!
| MAXIMUM EXTERNAL SURFACE TEMPERATURE: 185° F (85° C)
MAXIMUM AMBIENT TEMPERATURE: 104° F (40° C)
- DO NOT TOUCH the fixture housing during operation.
- Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before serving.
- DO NOT shake fixture, avoid brute force when installing and/or operating fixture.
- DO NOT operate the fixture if the power cord is frayed, crimped, damaged, and/or if any of the power cord connectors are damaged and do not insert into the fixture securely with ease.
- NEVER force a power cord connector into the fixture. If the power cord or any of its connectors is damaged, replace it immediately with a new one of a similar power rating.
- DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between the fixture and a wall for proper cooling.
- When installing fixtures in a suspended environment, always use mounting hardware that is at least M10 x 25 mm, and always install fixtures with an appropriately rated safety cable.
- Always disconnect fixtures from the main power source before performing any type of service and/or cleaning procedure.
- Only handle the power cord by the plug end, and never pull out the plug by tugging the wire portion of the cord.
- During the initial operation of this fixture, light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time.
- Consistent operational breaks will ensure fixtures will function properly for many years.
- In the event that the fixture needs to be returned for servicing, use only the original packaging and materials to transport the fixture.
OVERVIEW
INSTALLATION
FLAMMABLE MATERIAL WARNING
Keep fixtures a minimum of 5.0 feet (1.5m) away from flammable materials
and/or pyrotechnics.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or
installations.
THE MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS).
THE MINIMUM DISTANCE OF INFLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET
(0.5 METERS)
DO NOT EXPOSE TO RAIN OR MOISTURE!
INDOOR USE ONLY!
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
- Fixtures MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
- The ambient temperature operating range is -4°F to 158°F (-20°C to 70°C). Do not use operate the unit when the ambient temperature falls outside of this range!
- Device(s) should be installed in areas outside walking paths, seating areas, or areas where unauthorized personnel might reach the fixture by hand.
- Allow approximately 60 minutes for the fixture to cool down before servicing.
IP RATING
This device is IP20 rated. This means that the unit is protected against
intrusion from solids approximately the size of an adult finger (12mm in
diameter), and that the unit is NOT protected against water intrusion of any
kind!
CONNECTIONS
Each of the three (3x) Power Out connections should be linked via a power
cable to a single Power Ramp from the MDF2 system. When used in conjunction
with the MDF2PSUX20 power supply, each Power Ramp is able to support a single
row of up to twelve (6x) dance floor tiles, for a total of eighteen (18x)
dance floor tiles.
When installing the dance floor panels in place, pay close attention to the
directional orientation arrows located on the side faces of each panel. When
placed correctly, these arrows should indicate the direction of power flow
from the Power Ramp to the first panel, then to each subsequent panel down the
line. These panels must be positioned in a straight line to receive and
transmit power. If the panel is rotated 90 degrees, or if the panel is
placed with the directional arrow pointing back towards the power source, the
panel will not receive power or be able to transmit power to any subsequent
panels down the line.
Please see the illustration below, or refer to the user manual for the ADJ
MDF2-9SYS for detailed information.
Note: The top row of ramps in the illustration (shown in green) are Power
Ramps. All other ramps shown are non-powered Dummy Ramps.
NOTE: Directional orientation arrows are depicted on the top surface of the panels for the sake of clarity. Actual panels will have directional orientation arrows located on the sides of the panels.
TROUBLESHOOTING
Below are some common issues that you may encounter during use, along with possible solutions. If the steps below do not solve your problems, please contact the ADJ support line at the phone number or e-mail address listed in the Introduction section of this manual.
No voltage output from power supply:
- Check that there is voltage output from the power socket.
- Check whether the fuse has been tripped. If so, replace the fuse. It is also strongly advised to check the layout of the dance floor panels to make sure that have been oriented correctly, in order to avoid tripping the fuse again.
- Check that the cable connecting the power supply to the dance floor assembly is securely connected.
Fuse or circuit breaker trips repeatedly:
- Check whether the power demand exceeds the maximum load output of the power supply. If so, reduce the number of dance floor panels connected to this power supply.
- Check whether the fuse itself is faulty. Replace the fuse with a new fuse of the correct type.
- Check the condition of the dance floor panels themselves to ensure that they are not working in an abnormal manner.
ELECTRICAL
Input Voltage: AC 100-240V, 50/60 Hz Output Voltage: DC 24V
Maximum Load Power: 2250 W Load Current: 90 A
Current Overload Protector Trip Time:
- Within 10A of max load: no trip
- 10-15A over max load: trip within 1 hour
- 15-20A over max load: trips in 5.2 to 30 seconds
- 20-30A over max load: trips in 1.5 to 5.5 seconds
DIMENSIONS
Length: 12.8” (326.0mm)
Width: 5.6” (142.0mm)
Height: 6.1” (155.5mm)
Weight: 30.0 lbs (13.6 kg)
AMBIENT OPERATING CONDITIONS
Ambient Operating Temperature: -4°F to 158°F (-20°C to 70°C)
IP Rating: IP20
INCLUDED ITEMS
Power Cable (x1)
DIMENSION DRAWINGS
Dimensions not to scale
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
included instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one
or more of the following methods:
- Reorient or relocate the device.
- increase the separation between the device and the receiver.
- Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to helping to protect the environment. Please
turn off all electrical products when they are not in use. To avoid power
consumption in idle mode, disconnect all electrical equipment from power when
not in use. Thank you!
©2022 ADJ Products, LLC all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without
notice. ADJ Products, LLC logo and identifying product names and numbers
herein are trademarks of ADJ Products, LLC. Copyright protection claimed
includes all forms and matters of copyrightable materials and information now
allowed by statutory or judicial law or hereinafter granted. Product names
used in this document may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged. All non-ADJ Products, LLC
brands, and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages,
injuries to any persons, and direct or indirect economic loss associated with
the use or reliance of any information contained within this document, and/or
as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.
ADJ USA
6122 S. Eastern Ave.
Los Angeles, CA. 90040
323-582-2650
323-532-2941 fax
www.adj.com
support@americandj.com
ADJ Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade, The Netherlands
+31 (0)45 546 85 00
+31 45 546 85 99 fax
www.adj.eu
support@adjgroup.eu
ADJ Mexico
AV Santa Ana 30
Parque Industrial Lerma, Lerma, Mexico 52000
+52 728-282-7070
DOCUMENT VERSION
https://www.adj.com/mdf2psux20
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update
of this manual
Date
| Document
Version| Software
Version| DMX Channels|
Notes
---|---|---|---|---
03/29/22| 1.0| N/A| Not Applicable| Initial Release.
| | | |
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>