cameo OTOS SP6 GOBOS IP65 Spot Profile Moving Head User Manual
- June 13, 2024
- cameo
Table of Contents
USER MANUAL
OTOS® SP6 GOBOS
IP65 SPOT PROFILE MOVING HEAD – GOBO
NOTES ON GOBOS AND GOBO REPLACEMENT
These installation instructions do not replace the user manual of the
associated product!
The gobos in both gobo wheels of the spotlight are interchangeable. Below are
images of the gobos in both gobo wheels.
ATTENTION:
Gobos may only be replaced by qualified specialist personnel. If you are not
qualified to do this, do not try to replace gobos yourself. Refer instead to
professional companies.
When replacing gobos, pay close attention to each step in the OTOS SP6 Moving
Head User Manual under REPLACING GOBOS.
GOBO WHEEL 1, ROTATING GOBOS
GOBO WHEEL 2, FIXED GOBOS
ALIGN THE GOBO CORRECTLY
When replacing a gobo, make sure that the gobos are inserted in the
corresponding holder in the correct orientation and that there is sufficient
heat resistance; otherwise heat damage to the gobos and gobo holders may
occur. For proper orientation of the gobo, refer to the drawings and
descriptions below. However, if there is any doubt about the orientation and
heat resistance of a particular gobo type, please contact the gobo
manufacturer.
Insert a coated glass gobo into the corresponding gobo holder so that the more
reflective side of the gobo faces the light source. The less reflective side
of the gobo absorbs less heat in this way.
Gobos with a defined orientation (e.g. text gobos) are correctly displayed in the projection if they are correctly displayed when viewed from the side facing the light source.
Glass gobos with surface structure are generally aligned with the structured side towards the light source. In most cases, the gobo is glued into the gobo holder with the help of a heat-resistant special adhesive, as the uneven surface prevents secure installation with a retaining spring.
TECHNICAL DATA
| Product type: | Gobo wheel 1, rotating gobos | Gobo wheel 2, fixed gobos |
|---|---|---|
| Outer Ø: | 23 mm (+0 / – 0,2) | 30 mm (+0 / – 0,2) |
| Ø motif: | 19 mm (+0 / – 0,2) | 19 mm (+0 / – 0,2) |
| Material: | Borosilicate glass | Borosilicate glass |
| Material thickness: | 1.5mm | 1.5 mm |
| Heat resistance: | 600°C | 600°C |
MANUFACTURER GUARANTEE & LIMITATION OF LIABILITY
Our current warranty conditions and limitation of liability are available
under:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_CAMEO.pdf
In the event of service requirements, please contact Adam Hall GmbH, Adam
Hall-Str. 1,
61267 Neu-Anspach, Germany. E-mail:
Info@adamhall.com / +49 (0)6081 / 9419-0
CORRECT DISPOSAL OF THIS PRODUCT
(Valid in the European Union and other European countries with waste
separation)
This symbol on the product or associated documents indicates that the device
must not be disposed of together with normal household waste at the end of the
product’s service life, in order to prevent environmental damage or personal
injury due to uncontrolled waste disposal. Please dispose of this product
separately from other waste and recycle it to promote sustainable commercial
activity. As a private customer, you can obtain information on
environmentally-friendly disposal options from the seller of the product or
the appropriate regional authorities. As a commercial user, please contact
your supplier and check for any contractually agreed conditions on disposing
of the equipment. This product must not be disposed of with other commercial
waste.
SUBJECT TO MISPRINTS AND ERRORS, AS WELL AS TECHNICAL OR OTHER
MODIFICATIONS!
Cameo® is a registered brand of the Adam Hall Group
Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.co
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>