VOLLRATH 2350053-1 Meat Grinder Chamber Installation Guide
- June 13, 2024
- VOLLRATH
Table of Contents
VOLLRATH 2350053-1 Meat Grinder Chamber
Product Information
The product is a meat grinder designed for grinding and processing meat. It
consists of various components, including a grinder chamber, blade shaft, worm
gear assembly, shaft washer, knife blade, grinder plate, and coupling cover.
The meat grinder is equipped with sharp blades that can cause cuts and
amputation if not handled with caution. It is important to follow safety
precautions to avoid personal injury or propertydamage.
The product should not come into contact with water or other liquids to
prevent electrical shock. The power cord should be checked for damage and
should not be modified. An extension cord should not be used with the unit.
Product Usage Instructions
Assembly Procedures
- Turn the meat grinder off and unplug from its power source.
- Thoroughly clean and dry all parts.
- If necessary assemble the blade shaft (B) into the worm gear (A).
- Inspect the shaft washer (A) for wear. Replace if necessary.
- Slide the shaft washer (A) onto the worm gear shaft (B).
- Slide the shaft washer (A) so that it is seated against the worm gear assembly (B) as shown.
- Slide the worm gear assembly (B) and the shaft washer (A) into the grinder chamber (C). Slide the worm gear shaft (D) in until it is seated fully.
- Slide the knife blade (B) so that the flat ground edges (A) face to the outside as shown, onto the blade shaft (C).
- Slide the knife blade (B) onto the blade shaft (C) so that it seats completely over the square (D).
- Place the grinder plate (D) onto the blade shaft (A) so that the cutout (C) slides over the locating pin (B).
- If a sausage filler is to be used, place it between the coupling cover (A) and the grinder chamber (B).
- Thread the coupling cover (A) onto the grinder chamber (B) and tighten securely.
Disassembly Procedures
- Turn the meat grinder off and unplug from its power source.
- Unscrew and remove the coupling cover (A) from the grinder chamber (B).
- Remove the grinder plate (D) from the blade shaft (A).
- Carefully remove the knife blade (B) from the blade shaft (C).
- Remove the worm gear assembly (B) from the grinder chamber (C).
- Thoroughly clean and dry all parts.
Please refer to the product manual for further details and safety precautions.
For additional information, visit
www.vollrathco.com or contact The Vollrath
Company, L.L.C. at the provided address.
To ensure safe installation and operation, read the following statements and
understand their meaning. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that can cause severe
personal injury, death, or substantial property damage if the warning is
ignored.
Safety Precaution
WARNING
Electrical Shock Hazard.
Keep water and other liquids from entering the inside of the unit. Liquid
inside the unit could cause an electrical shock.
Do not spray water or cleaning products. Liquid could contact the electrical
components and cause a short circuit or an electrical shock. Do not use unit
if power cord is damaged or has been modified. Do not use an extension cord
with this unit.
WARNING
Sharp Blade Hazard.
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal
should operate equipment or preform maintenance.
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830 Fax: 800.752.5620
Technical Services: 800.628.0832 Service Fax: 920.459.5462
Canada Service: 800.695.8560
© 2010 The Vollrath Company, L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>