VOLLRATH VOL-4076005 Meat Grinder Chamber and Components Instruction Manual

: June 13, 2024
: VOLLRATH

Table of Contents

VOLLRATH VOL-4076005 Meat Grinder Chamber and Components
Product Information
Product Usage Instructions
Assembly and Disassembly
Contacts
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH VOL-4076005 Meat Grinder Chamber and Components

VOLLRATH-VOL-4076005-Meat-Grinder-Chamber-and-Components-
product

Product Information

The product is a Meat Grinder designed for grinding meat and making sausages. It has various components including a grinder chamber, blade shaft, worm gear assembly, shaft washer, knife blade, grinder plate, and coupling cover. The meat grinder is equipped with a sharp blade that can cause cuts and amputation if not handled with caution. It also has electrical components, and therefore, water and other liquids should be kept away from the inside of the unit to avoid electrical shock hazards.

Product Usage Instructions

Assembly Procedures

Turn off the meat grinder and unplug it from the power source.
Thoroughly clean and dry all parts.
If necessary, assemble the blade shaft into the worm gear.
Inspect the shaft washer for wear and replace if necessary.
Slide the shaft washer onto the worm gear shaft and seat it against the worm gear assembly.
Slide the worm gear assembly and the shaft washer into the grinder chamber until fully seated.
Slide the knife blade onto the blade shaft with the flat ground edges facing outward.
Slide the grinder plate onto the blade shaft so that the cutout slides over the locating pin.
If using a sausage filler, place it between the coupling cover and the grinder chamber.
Thread the coupling cover onto the grinder chamber and tighten securely.

Disassembly Procedures

Turn off the meat grinder and unplug it from the power source.
Unscrew and remove the coupling cover from the grinder chamber.
Remove the grinder plate from the blade shaft.
Carefully remove the knife blade from the blade shaft.
Remove the worm gear assembly from the grinder chamber.
Thoroughly clean and dry all parts.

For more information and support, please visit www.vollrathco.com.

Assembly and Disassembly

To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.

WARNING: Warning is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

Safety Precautions

WARNING: Electrical Shock Hazard.

Keep water and other liquids from entering the inside of the unit. Liquid inside the unit could cause an electrical shock.
Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock.
Do not use unit if power cord is damaged or has been modified. Do not use an extension cord with this unit.

WARNING: Sharp Blade Hazard.

Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.

Assembly Procedures

Turn the meat grinder off and unplug from its power source.
Thoroughly clean and dry all parts.
If necessary assemble the blade shaft (B) into the worm gear (A). See Figure 1.
Inspect the shaft washer (A) for wear. See Figure 2. Replace if necessary.
Slide the shaft washer (A) onto the worm gear shaft (B).
Slide the shaft washer (A) so that it is seated against the worm gear assembly (B) as shown. See Figure 3.
Slide the worm gear assembly (B) and the shaft washer (A) into the grinder chamber (C). Slide the worm gear shaft (D) in until it is seated fully.
Slide the knife blade (B) so that the flat ground edges (A) face to the outside as shown, onto the blade shaft (C). See Figure 4.
Slide the knife blade (B) onto the blade shaft (C) so that it seats completely over the square (D). See Figure 5.
Place the grinder plate (D) onto the blade shaft (A) so that the cutout (C) slides over the locating pin (B). See Figure 6.
If a sausage filler is to be used, place it between the coupling cover (A) and the grinder chamber (B). See Figure 7.
Thread the coupling cover (A) onto the grinder chamber (B) and tighten securely.

Disass embly Procedures

Turn the meat grinder off and unplug from its power source.
Unscrew and remove the coupling cover (A) from the grinder chamber (B). See Figure 7.
Remove the grinder plate (D) from the blade shaft (A). See Figure 6.
Carefully remove the knife blade (B) from the blade shaft (C). See Figure 5.
Remove the worm gear assembly (B) from the grinder chamber (C). See Figure 3.
Thoroughly clean and dry all parts.