Ballu NCA1-3.0EF-Pro Digital Electric Convector Inverter Instruction Manual

Ballu NCA1-3.0EF-Pro Digital Electric Convector Inverter

COMPONENTS

Name of components and parts

FOOT INSTRUCTIONS

Before using this heater,it must either be wall mounted or have the feet fitted.The device has provided special screw knobs for mounting the feet, which can be installed manually without using a screwdriver.

Product Components

Installation

Before you install:

1. Make sure the heater is unplugged and power switches are off
2. Carefully turn the main body upside-down on a scratch-free and stable surface. Be careful to prevent damage to the cosmetic finish or your floor surfacing.

Note: The wall bracket edges may be sharp.it is recommended that if using as a free standing appliance please remove the wall bracket from the back of the heater

Foot installation

WALL MOUNTING INSTRUCTIONS

Note:

1. The appliance must not be located inmediately below a socket outlet.
2. Your Panel Heater should be installed with at least 150mm clearance from the floor and any other surrounding parts including other appliances and side walls.At least 300mm clearance from ceilings, shelves and soft furnishings.
3. Do not run the power cord behind the heater.

WALL MOUNTED HEATERS AREONLY TO BE MOUNTED ON HEATRESISTANT WALLS THAT COMPLYWITH CURRENT SPECIFICATIONS & BUILDING REGULATIONS

WALL MOUNTED

1. Make sure the appliance is unplugged and power switches are off.
2. Position the panel appliance within one metre of wall socket. Do not mount in front of orbelow the wall socket. Ensure there is at least 150mm clearance on all sides of the appliance.
3. Position the mounting bracket in the wall and mark the hole positions with a pen or pencil and check they are horizontal with a spirit level. Ensure the two bottom mount holes are at least 150mm from the floor and drill holes as required.
4. Secure the mounting bracket to the wall with the mounting screws. (For masonry walls use the plastic sheaths).
5. Insert the back of the device into the mounting bracket. First find the bottom plug,align and insert it, then align the upper hole and push it toward the wall. You can press down on the protruding part above the bracket so that the bracket slot can better enter the hole position.
6. Plug appliance into a standard 120 volt AC electrical outlet.

OPERATING YOUR HEATER

Control Panel

1. Power button
2. Boost mode
3. Menu and selection buttons
4. Mode switch and back button
5. Temperature control and screen
6. Display screen
7. Power Indicator light

Screen indication

• Yellow light – Comfort mode(50-86°F/10-30°C)
• Green light – Eco mode(50-86°F/10-30°C)
• Red light – Boost mode(86°F/30°C)
• Indication of heating power levels
• Control lock indication
• Indication of “Timer Off” function (to turn off)
• Display target temperature
• It is normal and harmless for a new product to smell when it is first used. It is recommended to heat for 2 hours at the maximum power in a ventilated environment, and then it can be used without smell
• The set temperature may deviate from the room temperature by 2-6°F, depending on the volume and insulation of the room. For large rooms that are easy to cooled quickly, we recommend setting the temperature 2-6 F higher than the desired temperature which will help improve heating efficiency
• If the product triggers overheating protection due to misuse, it will not work properly, you need to contact us at BalluCustomerService@gmail.com.

Main function

Mode & back button

1. Click to switch between 2 different modes
2. Comfort mode range from 50 to 86°F(10-30°C), the default value is 86°F (30°C),
3. ECO mode range from 50 to 86°F (10-30°C), the default value is 77°F (25°C),
4. The temperature values you set in different modes will be automatically saved.
5. Even at the same temperature setting, ECO mode will save about 2°F(1°C) of energy than Comfort mode

Boost mode button

1. Click the button to enter Boost mode.
2. Boost mode will reset the timer and power settings and will disregard the temperature settings. It will heat at full power of 1500w for 3 hours and will automatically switch to comfort mode after expiration.
3. In Boost mode the operation of setting temperature timer, power level and mode will cancel Boost mode.
4. Click the button again during the 3-hour period in boost mode will refresh the 3-hour timer

Menu & select button

1. Click to enter the menu, you can choose the “Wifi reconnect (reset network)” “Power Mode(750W/1500W)”, “Timer(0-24hour)”, “Settings(‘F/C)”, “Brightness(50%/100%)”, “Sound(ON/OFF)” by Move button.
2. Scan the QR code to download the app, connect your phone to Wi-Fi and turn on Bluetooth. then click on the “+’ * icon in the top right corner of the app to connect to the heater.

On/off button
Click to turn the product on or off. Turn off the product to enter standby mode
Move button
Click to increase or decrease the temperature setpoint. or move the meni scropn

Child lock function:

1. Press “<” and “>” simultaneously for 3 seconds to activate the lock function.
2. When the lock function is on, press the “<” and “>” buttons simultaneously for 3 seconds to turn off the lock function
3. The lock function can also be turned on and off in standby mode.

SETTINGS MENU DIAGRAM

Wifi settings
Press the menu button and select “Wifi reconnect” to reconnect the appliance . Power settings
Press the menu button and select “Power” to adjust the level1(750W/level2(1500W). Timer settings
Press the menu button and select ” Timer” to select the countdown time to turn off. O H cancel turn off. Temperature Unit setting
Press the menu button and select “Settings” -“Change units”to the select the unit. Reset program
Press the menu button and select “Settings” “Reset” to achieve. Brightness setting
Press the menu button and select “Settings”, select “Display”, select “Brightness”, you can choose the brightness level Sound settings
Press the menu button and select “Settings”, select “Sound”, you can choose to switch the sound on and off

Customer service
Press the menu button and select “Settings” “Customer service” to check service mail address and firmware version.

Other function

WIFI CONTROL

1. Download the app
   Search for Smart Life in Apple’s App Store and other major app stores or scan thefollowing QR code to download the Smart Life app.

2. Register an account
   According to the reminder to register an account with an email address or mobile phone number

3. Add a device

4. Tap Add Device or the plus icon (+) in the top right corner on the Home page to go to the device adding page. On the Add Device tab that appears, devices can be automatically found or manually added. The app must be granted 2.4 GHz Wi-Fi and Bluetooth permissions. This method enables simultaneously searching for multiple devices, including Wi-Fi devices, Bluetooth gateways, Bluetooth mesh devices. All devices found can be added with one tap.

5. If the product cannot connect, please reset the device’s WiFi by following these steps: Menu > WiFi reconnect > YES. Then, check if your phone is already connected to 2.4 GHz WiFi and Bluetooth is enabled. Close and restart the app, and proceed to the first step to search and reconnect.

6. Function usage

TROUBLESHOOTING

Note:
The troubleshooting section below is for solving frequently asked questions for the heater unit. If your problem persists, please contact customer support .

Questions and Answers

1. Why does it smell when I use it?
   • A: To protect the metal of new products, we add a layer of protective oil to the surface. During the first use of the heater there may be some odor, this is considered normal and not harmful to health. For first use, we recommend turning on the product at maximum power (86°F) for approximately 2 hours in a ventilated environment to remove the odorit is also possible that the odor is caused by hair or dust in contact with the heatng element. Please make sure that no forein objects get inside the heater.
2. Why does the room warm up slowly?
   • A: convection heating process is soft and comfortable, generally need at least 1 hour to heat the full  room, the specific time spent on heating is affected by the use of the area, house warming effect, thesurrounding environment and other factors. During use it is recommended to close doors and windows to prevent heat loss and to keep the heater temperature set at a maximum of 86°F(30 C).This helps to warm up the room faster.
3. Why do you sometimes hear switch sounds?
   • A: The heater is equipped with a temperature sensor and automatic operation mode, when the set temperature on the heater is reached in the room, the heater automatically switches off the heating, so it is possible to hear the switch switching sound at that moment.
4. What is the difference between this Ballu convection heater and other oil heater?
   • A: Oil heaters heat the medium(oil) and then heat the air, which will cause too much heat to be wasted in the mediun(oil), resulting in low thermal efficiency. Because the heat loss rate of the room is fast, the thermal efficiency of the oil heater is low and there is no continuous heating effect, so th room temperatrue will be lower. Ballu convection electric heater direcrly heats the air through special alloy heating material, without intermediate medium, with high thermal efficiency, rapid room temperature rise, and by virtue of natural air convection, the indoor temperature is very uniform.
5. What is the difference between Ballu convection heater and air conditioner?
   • A: The air conditioner will cause the indoor air to flow sharply, which will make people feel dry and lack of oxygen, and because the installation position of the air conditioner is high, it will cause the experienceof hot head and cold feet. In addition, the air exchange principle of the air conditioner determines its heating effect. When the outdoor temperature is very low, the air conditiner loses its heating effect. The Ballu convection heater is based on the physical principle of hot air rising and cold air falling to achieve natural air convection without direct blowing, and can make the temperature of the upper and lower positions of the room the same, and the heating feels very comfortable.
6. How to save on electricity bills?
   • A: Power consumption depends on the size of the room, the insulation of the room, and the temperature you expect. It is recommended to use in a space of 160-220 square feet(Can be used up to 300 square feet, but requires longer heating time), close doors and windows to reduce heat loss, and adjust the  heater to the highest temperature and power for faster heating. When the room enters the thermalinsulation state, the temperature will be stable, and the power consumption per hour will be reduced. At this time, a lower temperature value can be set. You can also save on electricity bills with different mode temperatures, which are used at different times of the day and in different situations.

CARE AND CLEANING

• The heater requires regular cleaning to ensure trouble free.
• Unplug the heater from the mains supply before cleaning.
• Ensure that the heater has been allowed to cool down completely before cleaning.
• The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
• Use a soft cloth (not wet) to wipe the exterior of the heater to remove dust and dirt.
• Never use solutions such as petrol, thinners or polishing agents.
• Ensure the heater is dry before plugging back into the mains supply.

IMPORTANT SAFETY INSTRUCTIONS

Thank your for choosing Ballu heater.Please read all instructions before using the appliance.When using any electrical appliance,some basic safety precautions should be observed to reduce the risk of fire, electric shock,and/or any injury to persons.

CAUTION: To avoid danger due to inadvertent restarting, this equipment must not be powered through an external switching device (such as a timer) or connected to a circuit that is periodically switched on and off by a utility.

• This equipment is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they are supervised or instructed in the use of the equipment by a person responsible for their safety.
• If the power cord is damaged, it must be replaced by the manufacturer, its service facility, or similarly qualified personnel to avoid a hazard.

WARNING: You must not cover this heater. Covering this appliance is a fire hazard and will trip the safety fuse, permanently disabling the heater.
WARNING: Extreme caution is necessary when any heater is used by or near children or those in need of assistance, especially whenever the heater is left operating and unattended.
WARNING: To reduce the risk of fire keep textiles, curtains, or any flammable material a minimum distance of 1 metre from the air outlet.

• Use only the voltage specified on the rating label of the appliance.
• This appliance is intended for household use only and not for commercial or industrial use.
• Indoor use onlv.
• Use this appliance only as described in this manual.
• Do not use the appliance if it has been dropped or damaged.
• The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
• Do not operate in areas where petrol, paint or other flammable liquids are used or stored.
• Never use the appliance to dry clothes.
• Always unplug appliance when not in use.
• When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the appliance has been damaged, contact the Customer Services Team.
• Do not use if there are visible signs of damage to the heater and contact the customer to replace a new one.
• Do not connect the heater to the power supply until it is fully assembled and adjusted.
• Ensure hands are dry before handling the plug or main unit.
• Ensure appliance is on a flat, stable, heat- resistant surface.
• Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to become a hazard.
• Carry out regular checks of the supply cord to ensure no damage is evident
• Do not operate this appliance with a damaged cord, plug or after the appliance malfuntions or has been dropped or damaged in any manner. Take to a gualified electrical person for examination, electrical service or repair.
• Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use.
• It is recommended that this appliance is plugged directly into the wall socket. Power boards are not rated to supply power to high wattage appliances.
• Do not remove plug from power socket until the appliance has been switched off.
• Do not remove plug from power socket by pulling cord; always grip plug.
• Do not place cord under carpet or cover with rugs or furniture. Arrange the cord so it cannot be tripped over.
• Don’t place appliance on bedding or on thick & long carpet where the openings may get blocked.
• Switch off and use handle provided when moving
• Do not place appliance close to radiant heat source.
• Do not insert or allow foreign objects to enter any ventlation or exhaust opening, as this may cause an electric shock, fire or damage to the appliance.
• Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming pool or other liquids.
• The appliance must not be immersed in any liquids.
• This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science, etc. are stored.
• If your appliance does not work, or is not working properly, contact the Ballu Customer Services Team.

FCC

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subiect to the follow -ing two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).

WARRANTY AND SERCIVE

24-month warranty
This product is covered with ballu product and labor warranty for 24 month from the date of its original purchase.Please feel free to contact us for any problems about the maintenance and use of products.

The warranty will not apply in cases of:

• Accident, misuse, or repairs performed by unauthorized personnel.
• Any unit that has been tampered with or used for commercial purposes.
• Use of force, damage caused by external influences.
• Damage caused by non-compliance with user guidelines, e.g., connection to an unsuitable power source or non-compliance with instructions. Partial or complete disassembly of the appliance.

After Sales Service
If If any problem occurs, you can check the manual for troubleshooting in detail, or contact to our customer service on Amazon.

To contact authorized Amazon seller, please following steps:

• Step 1: Go to Your Orders. Find your order in the list.
• Step 2: Click “Ask a question”. (Or go to the product detail page,select the name of the seller. On the next page, select “Ask a Question”.)
• Step 3: Select the product and tap “Other” options in the Seller Messaging Assistant chat
• Step 4: Send the message to us for after-sales support.

We always work hard to serve you and provide you a better customer experience.
Customer service: BalluCustomerService@gmail.com.

CONTACT

• Customer service: BalluCustomerService@gmail.com.
• Manufacturer: Foshan Shunde BIG Climatic
• Manufacture Co., Ltd
• Address: C area, 2nd Floor, 9A building, factory
• buildings 2 and 3, section no. 10-6, Fu An industrial
• area (First phase), Leliu Town, Shunde District,
• Foshan City, Guangdong, China

For the correct usage of the product, read the user manual carefully and keep it nearby. https://ballu.world/.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>