RAB ECOMBO34 LED Exit Combo Sign Emergency Light Instructions

RAB ECOMBO34 LED Exit Combo Sign Emergency Light Instructions

Wall Mount Installation

1. De-energize the circuit at the junction box where the exit sign is to be installed.

2. Remove the exit sign stencil and set aside. Remove the hardware and LED Lamp heads and set aside. Remove and discard the plastic canopy and mounting plate.

3. Drill out the appropriate mounting pattern and the wire pass hole in the EXIT back plate to t the junction box being used.

4. Feed the red, black and white wires through the center.

5. Remove side mounting hole plug on right side. Knockout lamp head mounting hole on left side with athead screwdriver.

6. Feed blue and yellow lamp head wire through side lamp head mounting hole(Fig 1)
   
   Attach first lamp head to housing by aligning tabs on lamp head assembly to lamp head mounting slots on frame of housing (Fig 2).
   
   Gently push lamp head down toward bottom of housing to lock into place. An audible click should be heard. Repeat to install remaining lamp head.

7. Feed lamp head wires in appropriate wire channel and connect lamp head leads to the exit sign lamp board.

8. Reference wiring diagram and make proper electrical connections at the junction box in the metal housing.

9. Fastsdden back plate to junction box cover.

10. Connect battery only after continuous AC power can be provided to the unit.

11. Remove proper Chevron(s) as required.

12. Secure face plate to housing

Ceiling Mount Installation

1. De-energize the circuit at the junction box where the exit sign is to be installed.
2. Remove the exit sign stencil and set aside.
3. Remove the canopy kit, hardware pack, mounting plate and LED lamp heads from inside the EXIT and set aside.
4. Remove the mounting hole plug on the top of the frame.
5. Place the canopy nose through the mounting hole until the side of the frame touches the canopy. Lock the frame onto the canopy by sliding the frame in a direction parallel to the canopy length toward the narrow end of the mounting hole. Slide the frame until both snaps engage the canopy nose preventing any motion back out of the hole.
6. Feed the red, black and white wires through center of mounting canopy hole.
7. Remove side mounting hole on right side. Knockout lamp head mountinghole on left side with athead screwdriver.
8. Feed blue and yellow lamp head wire through side lamp head mounting hole (Fig 1). Attach rst lamp head to housing by aligning tabs on lamp head assembly to lamp head mounting slots on frame of housing(Fig 2).Gently push lamp head down toward bottom of housing to lock into place. An audible click should be heard. Repeat to install remaining lamp head.
9. Feed lamp head wires in appropriate wire channel and connect lamp head leads to the exit sign lamp board.
10. Reference wiring diagram and make proper electrical connections at the junction box in the metal housing.
11. Secure the EXIT canopy to the steel mounting plate using the screws provided and fasten to junction box.
12.  Connect battery only after continuous AC power can be provided to the unit.
13. Remove proper Chevron(s) as required.
14. Secure face plate(s) to housing

WIRING DIAGRAMS

NOTE: Unused input lead must be properly insulated with wire nut or other approved method.

STANDARD

REMOTE CAPABLE

End Mount Installation

1. De-energize the circuit at the junction box where the exit sign is to be installed.

2. Remove the exit sign stencil and set aside.

3. Remove the canopy kit, hardware pack, mounting plate and LED lamp heads from inside the EXIT and set aside.

4. Remove the mounting hole plug on the right side of the frame.

5. Place the canopy nose through the mounting hole until the side of the frame touches the canopy. Lock the frame onto the canopy by sliding the frame in a direction parallel to the canopy length toward the narrow end of the mounting hole. Slide the frame until both snaps engage the canopy nose preventing any motion back out of the hole.

6. Feed the red, black and white wires through the center of mounting canopy hole.

7. Knockout lamp head mounting hole on left side with athead screwdriver.
   Note: For single face, left side end mount, remove and switch back plate and face plate before installing the side mounted LED lamp head.

8. Feed blue a nd yellow lamp head wire through side lamp head mounting hole(Fig 1). Attach lamp head to housing by aligning tabs on lamp head assembly to lamp head mounting slots on frame of housing(Fig 2). Gently push lamp head down toward bottom of housing to lock into place. An audible click should be heard.

9. Feed lamp head wires in appropriate wire channel and connect lamp head leads to the exit sign lamp board.

10. Reference wiring diagram and make proper electrical connections at the junction box in the metal housing.

11. Secure the EXIT canopy to the steel mounting plate using the screws provided and fasten to junction box.

12. Connect battery only after continuous AC power can be provided to the unit.

13. Remove proper Chevron(s) as required.

14. Secure face plate(s) to housing.

Easy Answers

© 2023 RAB LIGHTING Inc.
Cranbury, New Jersey 08512 USA

rablighting.com
Visit our website for product info

Tech Help Line
Call our experts: 888 722-1000

e-mail
Answered promptly- sales@rablighting.com

Free Lighting Layouts
Answered online or by request

EXNY 3-IN-0323
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>