BORMANN BDS2500 Security safe electronic lock Instruction Manual
- June 13, 2024
- BORMANN
Table of Contents
BORMANN BDS2500 Security safe electronic lock
Product Information
Model Numbers:
BDS2500, BDS3000, BDS5000, BDS6000
Dimensions:
- BDS2500: L35 x D25 x H25 cm
- BDS3000: L31 x D20 x H20 cm
- BDS5000: L35 x D31 x H50 cm
- BDS6000: L43 x D38 x H20 cm
Technical Data
| Model | BDS2500 | BDS3000 | BDS5000 | BDS6000 |
|---|---|---|---|---|
| Door thickness | 3 mm | 3 mm | 4 mm | 3 mm |
| Body thickness | 1 mm | 1 mm | 1.5 mm | 1.5 mm |
| Dimensions | L35 x D25 x H25 cm | L31 x D20 x H20 cm | L35 x D31 x H50 cm | L43 x |
D38 x H20 cm
Parts
- Locking bolts
- Reset button
- Battery compartment
- Knob
- Emergency override keyhole cover
- Green light
- Red light
- Yellow light
- Confirm button
Product Usage Instructions
Opening the Safe with the Emergency Key
To open the safe for the first time, use the emergency key.
- Remove the emergency keyhole cover. (1-2)
- Insert the emergency key into the keyhole, turn it counterclockwise, then turn the knob clockwise to open the door. (3-4)
Inserting the Batteries
- Open the door.
- Insert 4x AA batteries into the battery compartment.
If both the red and green light are on at the same, it means that the battery
is low and that new batteries should be inserted.
Caution:
- Make sure to insert the batteries with the correct polarity by observing the ”+” and ”-” symbols.
- The user’s code should be reset whenever new batteries are inserted.
Setting the User Code
- Open the safe, press the reset button, wait until the yellow light comes on and then input the code.
- Input the new code (3-8 digits) and press the (A) or (B) button to confirm.
- You will hear a beep once the code has been accepted.
- If the yellow light flashes and a beep can be heard, it means that the code is invalid and the process will have to be repeated.
Opening and Closing of Door
Opening the Door
- Input your 3-8 digit code. Whenever a button is pressed, the safe emits a beep sound and the yellow light flashes.
- Press the (A) or (B) confirming button. The green light will turn on.
- Rotate the knob clockwise and pull outwards within 5 seconds to open the door.
Note:
The preset code is ”159”. Input the user code again if the yellow light
flashes and the safe emits beeping sounds.
Closing the Door
- Turn the knob counterclockwise to close the door.
Automatic Lock
-
3 continuously wrong code entries will activate the warning beeps.
Attention: -
The keypad is disabled during the beeping.
-
You can only stop the beeps by opening the safe with the emergency key or by removing the battery.
The manufacturer reserves the right to make minor changes to product design
and technical specifications without prior notice unless these changes
significantly affect the performance and safety of the products. The parts
described / illustrated in the pages of the manual that you hold in your hands
may also concern other models of the manufacturer’s product line with similar
features and may not be included in the product you just acquired.
To ensure the safety and reliability of the product and the warranty validity,
all repair, inspection or replacement work, including maintenance and special
adjustments, must only be carried out by technicians of the authorized service
department of the manufacturer.
Always use the product with the supplied equipment. Operation of the product
with non-provided equipment may cause malfunctions or even serious injury or
death. The manufacturer and the importer shall not be liable for injuries and
damages resulting from the use of non-conforming equipment.
IMPORTANT INFORMATION
- Never keep the emergency override keys inside the safe. Always keep the emergency keys in a safe place.
- The appearance of the model you have acquired may not correspond to the drawings in this manual, however, the mode of operation of all models mentioned in the technical data is the same.
MOUNTING
- Select a stable, dry and secure location to install the safe.
- If bolting to a wall, make sure that the safe is resting on a supporting surface (such as on the floor or on a shelf). Do not bolt the safe to both the floor and wall.
- Place the safe on the selected location. Use a pencil to mark the mounting holes on the floor or wall.
- Move the safe and drill 50 mm-deep holes (2 inches) using the appropriate drill bit.
- Move the safe back in the selected location and align the mounting holes with the openings in the safe.
- Insert the expansion bolts (included) through the holes and into the mounting holes and tighten them securely.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>