GYS 077164 Blind Rivets 24 Kn Adaptor Compact Instruction Manual
- June 13, 2024
- GYS
Table of Contents
BLIND RIVETS 24 kN ADAPTOR COMPACT
DESCRIPTION
077164
60 cm
24 kN
GYSPRESS 8T & 8T PUSH-PULL
GYSPRESS 10T & 10T PUSH-PULL
GYSPRESS 10T CONNECT
INSTALLATION ON GYSPRESS
GYSPRESS 8T
- Install the die D17 on the GYSPRESS 8T nose.
- Insert the blind rivet adapter on the GYSPRESS 8T nose.
GYSPRESS 8T PUSH-PULL
- It is not required to install a die on the GYSPRESS 8T PUSH-PULL nose.
- Remove the nut (1).
- Insert the blind rivet adapter on the GYSPRESS 8T nose.
GYSPRESS 10T
-
Insert the pin to lock the blind rivet adapter on the GYSPRESS.
-
The blind rivet adapter can be turned by 360°.
PRESSURE ADJUSTMENT
Set the pressure on the GYSPRESS to maximum.
NOSE PIECES CHANGE
To facilitate the installation of the nozzles:
-
Position a rivet in the nozzle
-
Insert the rivet between the jaws
-
Tighten the nozzle
-
Use a 12 mm open-end wrench.
-
2 nose pieces are supplied with the blind rivet adapter.
-
Measure the diameter of the mandrel to know which nose piece to use.
This table specifies which nose piece to use depending on the diameter of the blind rivet mandrel.
| Blind structural rivets | Adapter | Part numbers |
|---|---|---|
| Ø 6.4 / 7.8 | Ø 4.5 | |
| Ø 5.2 | 081222 |
079939
SETTING OF A BLIND RIVET
- Place the rivet mandrel as far as it will go from the adapter nose piece.
- Insert the rivet head into the appropriate hole.
- Operate the riveting machine.
RIVET MANDREL EVACUATION
- The rivet mandrel has to be removed from the front of the adapter.
- Tilt the head down to remove it.
IN CASE OF A RIVET MANDREL BLOCKED BY THE CLAMPING JAWS
If a too small nose piece has been used, the rivet mandrel might be blocked by
the clamping jaws.
In order to release it, please replace the nose piece with a larger one (Ø
5.2mm). This nose piece will push the clamping jaws to the maximum, releasing
the rivet mandrel.
CLAMPING JAWS CHANGE
-
Unscrew the back of the adapter (easier to unscrew than the front).
There will be no oil leak.
-
Extract the spring and the clamping jaws.
-
Replace with new ones.
-
Replace the spring.
-
Screw the back of the adapter again.
PRODUCT SERIAL NUMBER
- The serial number of the product is legible at the following location:
CONFORMITY ASSESSMENT
GYS certifies that the GYSPRESS conforms to the directive 206/42/EC and
respects the following standards :
EN 693 / EN 792-1 / EN 792-13
Date CE : 2022.
SPARE PARTS
| 1 | Reception base | M0520 |
|---|---|---|
| 2 | Canule arrière | M0524 |
| 3 | spring | 55360 |
| 4 | spring | 55359 |
| 5 | Canule avant | M0523 |
| 6 | spring | 55222 |
| 7 | Poussoir mors | M0522 |
| 8 | clamping jaw | 51522 |
SYMBOLS
| – Warning ! Danger of crushing hands.
---|---
| – Warning ! Danger of crushing fingers.
| – Respect general rules.
| – Wear gloves.
| – Wear a face mask.
| – Follow the user manual.
| – Recyclable product that falls within waste sorting recommendations.
SAS GYS
1, rue de la Croix des Landes
CS 54159
53941 SAINT-BERTHEVIN
Cedex France
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>