ring 5W21S8 Floodlight Wired Smart Lighting User Guide

ring 5W21S8 Floodlight Wired Smart Lighting

Product Information

The Floodlight Wired Smart Lighting is a high-quality lighting fixture that provides bright and efficient illumination for outdoor spaces. It is designed to enhance security and convenience by integrating with the Ring app and other compatible Ring devices. The floodlight is suitable for installation on a 4 round UL listed weatherproof electrical box.

Important Safety Precautions:

• Ensure that the power is disconnected at the fuse or circuit breaker before installing the floodlight.
• Verify that the supply voltage is correct (100 VAC~240 VAC 50/60 Hz).
• Properly ground the fixture to minimize the risk of electrical shock.
• Install the floodlight according to code standards and avoid placing it near combustible or flammable surfaces.
• Do not connect the floodlight to a dimmer switch or timer.
• If you are unfamiliar with working with electricity or lack experience, it is recommended to hire a licensed electrician.

Product Usage Instructions

Set up your Floodlight:

1. Download the Ring app on your iOS or Android device.
2. Follow the app instructions to set up and manage your Floodlight Wired.
3. Set up your Ring Bridge by referring to the instructions in the Ring app or Bridge user manual. The Bridge allows connectivity between your Ring Smart Lights and other compatible Ring devices.

Before you begin:
Ensure that you have all the necessary components included in the package:

• Screwdriver & Reversible Bit: Use this tool to install the mounting hardware.
• Foam Gasket: Attach this gasket to the back of the Plastic Mounting Plate to prevent water and debris from entering your junction box.
• Plastic Mounting Plate: Use this plate to attach the floodlight to your junction box securely.
• Bag o’ Screws: Find the appropriate screws in this bag for attaching the mounting hardware to your junction box.
• Metal Mounting Bracket: Screw this bracket into your junction box to secure the Plastic Mounting Plate.
• Wire Nuts (3): Use these nuts to connect the wires of your new Floodlight Wired with your existing wires.
• Hook: Utilize this hook to hang your Floodlight Wired, making it easier to connect the wires.

Note:
These instructions assume that you are replacing an existing floodlight or have a junction box available for mounting the Floodlight Wired. If you do not have a junction box, it is recommended to hire a licensed electrician to install one and ensure compliance with local building codes.

Install your Floodlight:
Follow these steps to securely install your Floodlight Wired:

1. Ensure the power is turned off at the circuit breaker for safety.
2. Attach the ground wire from your home to the ground screw inside the junction box. Do not attach it to the metal mounting bracket; instead, attach it directly to the junction box as indicated.
3. Proceed with the further installation steps provided in the user manual or follow the instructions in the Ring app for complete installation guidance.

By following these instructions, you can safely and effectively install and use your Floodlight Wired Smart Lighting. Enjoy the enhanced security and convenience provided by this product!

For your safety

• WARNING: Risk of electrical shock.
• Disconnect power at the fuse or circuit breaker before installing.
• Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source.
• Properly ground fixture.
• Always follow code standards when installing wired connections.
• CAUTION: Risk of fire. Do not install near combustible or flammable surfaces.
• NOTICE: Do not connect this light fixture to a dimmer switch or timer.
• Floodlight Wired must be installed on a 4” round UL listed weatherproof electrical box.
• This manual is for informational purposes only. Working with electricity can be dangerous unless proper safety precautions are taken. If you are not comfortable or are inexperienced with the processes and tools described in this manual, we recommend that you hire a licensed electrician.

Download the Ring app.

• The app walks you through setting up and managing your Floodlight Wired.
• Download it on your iOS or Android device.

Set up your Ring Bridge

• The Bridge connects your Ring Smart Lights to the Ring app and other compatible Ring devices.
• To set up your Bridge, follow the instructions in the Ring app or Bridge user manual.

Before you begin

Check out all the stuff in the box.

• Screwdriver & Reversible Bit
  Use to install the mounting hardware.

• Foam Gasket
  Attach this to the back of the Plastic Mounting Plate to keep water and debris out of your junction box.

• Plastic Mounting Plate
  Use this to attach to your junction box and secure your Floodlight Wired.

• Bag o’ Screws
  Find the right ones to attach the mounting hardware to your junction box without running to the hardware store.

• Metal Mounting Bracket
  Screw this into your junction box to secure the Plastic Mounting Plate.

• Wire Nuts (3)
  Use these to connect your new Floodlight’s wires to your existing wires.

• Hook
  Hang your Floodlight Wired to help make connecting the wires easier.

These instructions assume you’re replacing an existing floodlight and/or have a junction box where Floodlight Wired can be mounted. If you don’t have a junction box, then you’ll need to hire an electrician to install one.

Shut power off at the breaker

• You’ll be working with electrical wires during the install process. For safety’s sake, shut off power to your floodlight at the circuit breaker.
• If you don’t know where your breaker is or how to turn off power to your floodlight circuit, consult with a licensed electrician.

Remove your existing floodlight

With power off at the breaker, remove your existing floodlight from the junction box it’s attached to and disconnect the wires.

Floodlight Wired must be installed on a 4” round UL listed junction box. If you don’t have an existing junction box, you’ll need to hire a licensed electrician to install one. Be sure to comply with your local building codes.

Remove the bracket

• If there is a metal bracket attached to your junction box, remove that as well.
• Inspect your junction box to make sure water cannot get into it.

Install your Floodlight

Secure the ground wire.

• With power turned off at the breaker, attach the ground wire from your home to the ground screw inside the junction box.
• The included metal mounting bracket has a hole marked “GND”. DO NOT attach the ground wire to the metal mounting bracket. Attach it to your junction box as shown here.

Choose your screws.
Select a set of screws from the bags marked “A” through “E” that fit your junction box to secure the metal mounting bracket. One size does not fit all here, so we sent several.

• Bag A
  Standard screws. These should fit most junction boxes.

• Bags B & C
  Longer screws to reach the screw holes in recessed junction boxes.

• Bags D & E
  Best for older boxes with smaller screw holes.

We included a spare of all the screws and wire nuts just in case you drop one in the bushes (we did).

Attach the metal mounting bracket

• With the screws you selected in the previous step, secure the mounting bracket to your junction box using either pair of screw holes.
• Be sure to align the bracket so that the “FRONT” text faces outwards.

Attach the foam gasket.
Remove the tape from the foam gasket. Press the adhesive side firmly against the rear of the plastic mounting plate, making sure to align the center screw hole and wire slot on the foam gasket with the screw hole and wire slot on the plastic mounting plate.

Expose the wires.
Before securing the plastic mounting plate to your junction box, guide the wires coming from your home through the slot in the bottom of the plate to access them during installation.

Secure the plastic mounting plate

• Center the plastic mounting plate over the metal mounting bracket and secure it through the center screw hole with one of the screws from the bag marked “F.”
• Ensure the “UP” arrow on the plastic mounting plate points upwards for wall mounting, and away from the direction you want your motion sensor and lights to point for eave and overhang mounting.

To mount on an eave or overhang

• You’ll have to rotate the motion sensor in order to optimize it for horizontal motion detection.
• If you’re mounting vertically on a wall, skip ahead to page 24.

Rotate the Motion Sensor

• A. Push the motion sensor to the right, then rotate it counter-clockwise 180°.
• B. The motion sensor will now be facing the light heads, and “ring” will be upside down.

You may need to hold the motion sensor’s locking collar in place while rotating to keep it from unlocking.

Complete installation

• Follow the rest of the instructions in this manual or the Ring app.
• Once you’ve installed your Floodlight Wired should look like the image on the next page.

Hang it up

• Use the provided hook to hang your Floodlight from the installed plastic mounting plate to make wiring easier.
• Put one end of the hook into one of the mounting holes on your Floodlight, and the other into the slot on the plastic mounting plate.

Connect the power wires

• The white wire on your Floodlight is a neutral wire. Use a wire nut from the bag marked “G” to connect the white wire from your Floodlight to the white (or neutral) wire coming from your junction box.
• The black wire on your Floodlight is a hot wire. Use another wire nut from the bag marked “G” to connect the black wire from your Floodlight to the black (or hot) wire from your junction box.

If you don’t have clearly marked black and white wires coming out of your junction box, consult with a licensed electrician.

Mount your Floodlight

• Lift the Floodlight off of the hook, and remove the hook from the mounting plate. Push the wires through the slot in the plastic mounting plate and back into the junction box.
• Slide your Floodlight over the posts on the mounting plate. Grab a couple of screws from the bag marked “H” and use them to mount your Floodlight.
• Once your Floodlight is mounted, apply a weatherproof silicone caulk or sealant (not included) around the outside where the Floodlight housing and junction box meet to prevent water from collecting inside the junction box.

The motion sensor and lights are adjustable. Try various angles to find the best setting for your home.

Switch power back on

• You’re all set! Feel free to turn the power back on at the breaker.
• Your Floodlight will flash twice (and you may hear a “click”) to let you know it’s in Setup Mode.

Contact Information

For additional help, visit: ring.com/help Or

Give us a call

• US 1 800 656 1918
• Canada 1 855 300 7289
• Worldwide +1 310 929 7085

For a list of all our customer support numbers, visit: ring.com/callus.

Warranty

To review your warranty coverage, please visit www.ring.com/warranty.

Patents: www.ring.com/patents.

© 2019 Ring LLC or its affiliates.
Ring, Alexa, Always Home, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>