CLAS HU 1130BL Brake Bleeder and Manual Clutch User Manual

CLAS HU 1130BL Brake Bleeder and Manual Clutch

Product Information

The HU 1130BL Brake Bleeder and Manual Clutch 3L is a product designed to assist in brake fluid bleeding and manual clutch maintenance. It is manufactured by CLAS Equipements, a company based in Chignin, France.  The product is designed to release pressure from the brake andclutch systems, allowing for the removal of air bubbles and old fluid. It comes with a 3L tank capacity and features a release valve on the side of the pump for pressure release. For any issues or inquiries regarding the product, including installation problems, usage instructions, breakdowns, or manufacturing defects, customers are advised to contact CLAS Equipements directly. They can be reached via email at sav@clas.com, by phone at +33(0)4 79 72 69 18, or by visiting their website at clas.com. If customers wish to return the product due to a change of mind before installation, it should be returned prior to any installation attempts.

Product Usage Instructions

1. Ensure that there is no pressure remaining inside the unit. Release any pressure by using the release valve located on the side of the pump.
2. Remove the cap on top of the unit to access the tank.
3. Fill the unit with new brake fluid, ensuring that there is no old fluid or debris remaining in the tank.

Care and Maintenance: If components or parts are needed for the product, customers are advised to contact the reseller. For any problems encountered during usage, it is recommended to contact an authorized technician for assistance.

SAFETY INSTRUCTIONS

• Keep this product in good working order and condition, take immediate action to repair or replace damaged parts.
• Use approved parts only. Unapproved parts may be dangerous and will void the warranty.
• Keep children and unauthorised persons away from the work area.
• Keep work area clean and tidy and free from unrelated materials.
• Ensure the work area has adequate lighting.
• Do not use the kit to perform a task which it is not designed for.
• Do not allow untrained individuals to use the kit.
• Do not use the tool when you are tired or under the influence of drugs, alcohol or intoxicating medication.
• Dispose of waste liquids in accordance with local authority regulations.
• Always read and comply with the warnings on the brake fluid container.
• Wear eye protection and avoid contact with the fluid. If brake fluid gets into your eyes, rinse with plenty of water and seek medical advice. If swallowed, seek medical advice immediately.
  • Warning! Only use new brake fluid. Used brake fluid or other fluids will contaminate the system and possible brake system failure may occur.
  • Warning! Do not discharge fluids in an uncontrolled way, by which the environment will be polluted.
  • Warning! Brake fluid is flammable – keep it away from sources of ignition, including hot surfaces e.g. exhaust manifold.
  • Warning! Brake fluid will damage the paintwork. Any spillage should be flushed with water immediately.

OPERATING INSTRUCTION

1. Make sure no pressure remains inside the unit. Pressure can be released from the release valve on the side of the pump.
2. Remove the cap on top of the unit and fill the unit with new brake fluid. Make sure there is no remaining old fluid or debris in the tank.

FILLING PROCEDURE

1. Select a suitable adaptor from the selection provided with the unit. Install the adaptor to the master cylinder of the brake system.
2. Pump the handle of the unit up and down until the recommended bleeding pressure is reached. Open the brake nipple and connect it to the suitable bleeding container. Once seeing the new fluidcoming into the container, close the nipple. Repeat the process on all 4 wheels (in any order).
3. When the brake fluid is flowing, ask a helper to pump the brake pedal while you watch the fluid run through the clear tube. More than a few strokes may empty the master-cylinder reservoir, so remember to keep checking it and top it up if necessary.
4. Once the process is complete, release the pressure by pressing down the release valve by the side of the pump. After releasing, disconnect the fluid supply hose from the adaptor on the master cylinder. Note: Do not disconnect the adaptor before releasing the pressure.
5. If necessary top up the brake fluid in the reservoir to the maximum level. Replace the master cylinder cap on the vehicle.
6. Dispose the waste brake fluid in the bleeding container safely.

CARE AND MAINTENANCE

• After use, wipe clean with a clean, dry cloth.
• Air pressure must be released through the pressure relief valve.
• Empty the product tank when not in use.

CONTACT

• CLAS Equipements
• ZA de la CROUZA
• 73800 CHIGNIN
• FRANCE
• Tél. +33 (0)4 79 72 62 22
• Fax. +33 (0)4 79 72 52 86

PURGEUR FREIN ET EMBRAYAGE MANUEL 3L BRAKE BLEEDER AND MANUAL CLUTCH 3L If you need components or parts, please contact the reseller. In case of problems, please contact your authorized technician. clas.com.

WARNING

• Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.

Contact:

• You can reach us by mail sav@clas.com or by phone +33(0)4 79 72 69 18 or go directly to our website clas.com.
• If you have changed your mind regarding your purchase, please return this product before you attempt to install it.

References

• Accueil | CLAS© | Equipements & outillage | Garage solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>