COBY CPA902 True Wireless Party Speaker User Manual

**COBY CPA902 True Wireless Party Speaker User Manual

**

Buttons and parts

1.  Handle
2. USB Port
3.  TF Card Slot
4.  Power Switch
5. Micro-USB Charging Port
6. Status LED Indicator
7. 6.5mm Microphone Jack
8. 3.5mm Aux Port
9. Previous Track / Volume down Butto
10. Play/Pause / Scan Button
11. Next Track / Volume up Button
12. Mode/RGB Light Button
13. Microphone Storage Slot
14. Power Switch for the Microphone
15. Microphone Cable
16. 6.5mm Microphone Connector

Charging

To charge your speaker, connect one end of the provided US cable to the Micro- USB port on the top panel, then connect the other end to a USB power source. When the speaker i charging, the Status LED Indicator will glow red. When the charging is complete, the nicator wilting of.

Powering on / off

Powering on To power on your speaker, slide the Power Switch on the top panel to the “ON” position.

ON
 ingicator flashes blue quickly.
Power on tone notification

Powering off
“To power off your speaker, slide the power switch on the top panel to the “OFF” position.

OFF : The RGB ight and Status LED Indicator turn of,

NOTE: Ifthere is no operation on the speaker for § minutes after it turns on, it will automatically power of,

Bluetooth Mode

Bluetooth connection with your device When the speaker i on, it will automatically enter Bluetooth paring mode. Turn on Bluetooth n your device’s settings and search for “CPA9OZ”, then tap “CPASO2” to connect.

NOTE: The speaker will automatically be paired with your last successfully connected media device the next time it s turned on.

True Wireless Stereo connection

The CPAS02 supports True Wireless Paring, which lets you stream your music from your device to o CPAS02 speakers acting salt and right audio channels for definitive and immersive stereo sound quality. To pair two speakers together, follow the steps below:

1. Bring the two speakers next to each other and tur them on, Make sure neither speaker is connected to any other Bluetooth devices, such as your phone, tablet, or laptop.
2. Double press the Play / Pause Button on other speaker until you hear a tone notification, which means both speakers are paired with each other successfully.
3. Turn on your Bluetooth your device’s stings and search for “CPAS0Z” then tzp “CPAS02′ to connect. After they are successfully connected, you can scream music from your phone to both speakers.

NOTES:

1. Before pairing, ensure the speaker is not currently connected to another device. If it is, press and hold the Play/Pause button for 2 seconds to unpair the speaker from the current connected device.
2. The speaker will automatically be paired with your last successfully connected media device the next time it is turned on.
3. If there is no Bluetooth connection on the speaker for more than 5 minutes, it will automatically turn off.

For Music Playback

Note: When you receive or make a call, the music that is playing will automatically pause. The person’s voice on the other end of the line can only be heard through your phone. When you end the call, the music will resume.

FM Radio mode
In Bluetooth mode, press the Mode Button once to switch to the FM Radio mode. Insert the provided charging cable into the charging port as an antenna for better signals. Press the Scan Button once to search for the radio stations automatically, then all available radio stations will be stored by the preset channel number in order. Press the Scan Button again to stop the searching, and the speaker will automatically broadcast the last stored radio station.

Playing from external device

USB/TF card mode
Under any mode, insert a TF card into the TF card slot of your speaker, or insert a USB disk into the USB port of your speaker. It will make a tone notification, then automatically play the music files in the TF card/ USB disk. Repeat the same operation as in the “For Music Playback” section to contro the music playback.

Microphone Mode
The speaker has a 6.5mm Microphone Jack, which allows the user to connect the speaker with the
provided microphone: 1. Plug one end of the microphone cable into the Microphone Jack of the speaker, and the other end into the MIC Out port of the microphone.

2. Slide the Power Switch on the microphone to the “ON” position. Now you can stream your sound from the microphone to the speaker.

Tip:
To unplug the microphone cable from the microphone, press and hold the clip on the microphone connector, then pull to remove it.

• You can also connect other audio output instruments, such as electronic guitar and piano, using a microphone cable with a 6.5mm connector.

Aux Mode
Under any mode, connect one end of the 3.5mm AUX cable (not included) to the AUX IN port of your speaker, and connect the other end to the AUX OUT port of your source input device such as your phone, then the speaker will make a tone notification, to indicate that it enters the AUX mode.

NOTES:
Under AUX mode, you can mute the music playback sound, adjust the volume level on the speaker, and for other music playback controls, you can operate them through your media device. If a TF card, USB disk and Aux cable are plugged in simultaneously, you can press the Mode Button t switch between different modes. The mode will change as follows:

RGB Light Mode

There are 6 light modes available. Repeatedly press and hold the RGB Light Button to set your desired light mode (the RGB light is on the front panel). The light mode will change as follows:

NOTES:

• Under FM radio mode, the RGB light does not work.
• The speaker will display the last used light mode the next time it is turned on.
• When the battery is low, the RGB light may not work.

Specifications

Safety stament

Safety Precautions

1. Avoid dropping.
2. Do not disassemble this device.
3. Do not expose this device to rain or moisture or submerge in water.
4. Ideal temperatures are 0°C to 35°C. Avoid extreme temperatures.
5. Keep the device away from excessive heat, such as sunshine, fire or the like. 6. Do not use the device outdoors during thunderstorms.
6. Use original or certified cables.
7. Do not use any corrosive cleaner/oil to clean.
8. Keep out of reach of children. It contains small parts which may be a choking hazard. 10. Observe local laws and regulations while using the device.
9. To prevent damage to your device’s parts or internal circuits, do not use it in dusty, smoky, damp or dirty environments.
10. Do not use, store or transport the device where flammables or explosives are stored. Using your device in these environments increases the risk of explosion or fire.

FCC Statement

FCC ID: 2AMSOSTW002

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including nterference that may cause undesired operation Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

3. Reorient or relocate the receiving antenna.

4. Increase the separation between the equipment and receiver.

5. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

6. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Notice

This product complies with the radio interference requirements of the European Community.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Disclaimer

All information, design and specifications contained in this manual were correct at the time of this publication. As the product goes under continuous upgrades and changes, however, the final device may have slight differences. The contents of this manual are subject to change without prior notice, and Coby will not be liable for any errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this manual.

COBY COPYRIGHT© 2023 ALL RIGHTS RESERVED. COBY IS A REGISTERED TRADEMARK OF CBY HOLDINGS, LLC. MANUFACTURED BY SUMMIT ELECTRONICS LLC. USED UNDER LICENSE. CBY HOLDINGS, LLC DOES NOT MANUFACTURE THIS PRODUCT OR PROVIDE ANY MANUFACTUR- ER’S WARRANTY OR SUPPORT. THE BLUETOOTH WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED BY THE BLUETOOTH SIG, INC. AND ANY USE OF SUCH MARKS BY SUMMIT ELECTRONICS LLC IS UNDER LICENSE. OTHER TRADEMARKS AND TRADE NAMES ARE PROPERTY OF THEIR RESPECTIVE OWNERS.

WARNING: CANCER AND REPRODUCTIVE HARM- WWW.P65WARNINGS.CA.GOV

Bluetooth®

The Bluetooth’ word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Fesco Distributors, Inc. is under license. Other trademarks and trade names are those of thei respective owners.

SUMMIT ELECTRONICS LLC One Year Limited Warranty

SUMMIT ELECTRONICS LLC LIMITED WARRANTY (“Warranty”) – For product Categories Listed in Chart Below (as applicable, “Product”) Before returning your Product for service under this Warranty, please (i) read the instruction manual carefully. If you are still having trouble with your Product, please contact Technical Support at support@summitcegroup.com. Warning: Some Products may contain components that are small enough to be swallowed. Please keep out of reach of children. Subject to the terms and conditions herein, SUMMIT ELECTRONICS LLC (hereinafter called “SUMMIT ELECTRONICS LLC”) warrants to the original purchaser of the Product (“Customer”) that for the appli- cable Warranty Period listed below, the Product will be free from defects in material or workmanship under normal, non-commercial use (“Defects”).
Warranty Period encompasses, as listed below, separate “Coverage Periods” for Parts and Labor, each Coverage Period for one year, to begin from the original date of Customer purchase. If Customer returns a defective Product (or any component thereof) during the applicable Warranty Period, SUMMITELEC- TRONICSLLC will, at its option, during the specified Coverage Periods for Parts and Labor (as applica- ble) either: (i) repair the Product (or, as applicable, any component thereof) or (ii) replace the Product (or, as applicable, any component thereof) with a new or refurbished Product (or, as applicable, any component thereof), in either case free of charge to Customer for Parts and/ or Labor (as applicable) during the specified Coverage Period only, and excluding applicable shipping charges (noted below), for which the Customer is responsible. The foregoing states the Customer’s exclusive remedy and SUMMIT ELECTRONICS LLC’s sole liability for breach of the limited warranty contained herein. This Warranty specifically excludes any Product (or, as applicable, any component thereof) that has been subject to or Defects resulting from: (a) any neglect or misuse by a Customer, an accident, improp- er application, violation of operating instructions for the product, any other Customer-induced damage, or the alteration or removal of any product serial number: (b) any modification or repair to Product (or, as applicable, any component thereof) by any party other than SUMMIT ELECTRONICS LLC or a party authorized in writing by SUMMIT ELECTRONICS LLC; (c) any damage to Product (or, as applicable, any component thereof) due to power surges, incorrect electrical voltage, misconnection 17 to any device, or malfunction of any device used with the Product (or, as applicable, any component thereof); (d) cosmetic damage to the Product (or, as applicable, any component thereof) caused by normal wear and tear; (e) shipping damage that occurs while the Product is in transit; (f) damage caused by heat sourc- es, sunlight, electromagnetic conditions, or other climatic conditions; or (g) any acts of God. Product is sold to Customer for personal, non-commercial use only. Product is not warranted for Customer’s commercial or rental use. In addition, Product is not warranted against failure, and should not be used by Customer for any appli- cation where (i) there is a risk that any data stored on Product will be breached or otherwise compro- mised, or (ii) the data stored on Product is relied upon for medical or lifesaving applications. SUMMIT ELECTRONICS LLC disclaims any Warranty for any of the foregoing uses to the fullest extent permitted by law. Customer assumes any and all risks associated with such uses of Product and agrees to in- demnify SUMMIT ELECTRONICS LLC for any damages claimed against SUMMIT ELECTRONICS LLC for such uses. EXCEPT FOR EXPRESS WARRANTIES STATED ABOVE AND TO THE MAXIMUM EX- TENTPERMITTED BYLAW, THE PRODUCTS ARE PROVIDED “AS IS”, AND SUMMIT ELECTRONICS LLC DISCLAIMS ALLOTHER WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WAR- RANTY(1) OF ERCHANTABILITY, (II) OF FITNESS FOR APARTICULAR PURPOSE, OR (III) OF NON-IN- FRINGEMENT OF THIRD-PARTY RIGHTS. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL SUMMIT ELECTRO- NICS LLC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR PUNITIVE DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY LOST PROFITS OR REVENUES, LOSS OR IN- ACCURACY OF ANY DATA OR COST OF SUBSTITUTE GOODS, REGARDLESS OF THE THEORY OF LI- ABILITY (INCLUDING NEGLIGENCE) AND EVEN IF SUMMIT ELECTRONICS LLC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, SUMMIT ELECTRONICS LLC’S AGGREGATE LIABILITY TO CUSTOMER FOR ACTUAL DIRECT DAMAGES FOR

TO THE CUMULATIVE PRODUCT FEES PAID BY THAT CUSTOMER FOR THE PRODUCT CAUSING THE DAMAGES, IF ANY. This Warranty gives Customer specifics rights, and Customer may also have other rights that vary from jurisdiction to jurisdiction. o obtain Warranty service, Customer must email SUMMIT ELECTRONICS LLC Technical Support prior to making a Product return. Custorner must in- clude with Product return the following items (file to enclose any of these items may resulting a delay in the processing of your Warranty claim): (i) a dated sales receipt that indicates the place of purchase, model number of Product, and amount paid; i) a detailed description of Customer’s problem with Product; ii) Customer’ fll name, phone number, and return addfress, and; (v) a money order made out to SUMMIT ELECTRONICS LLC Electronics Corporation to cover return shipping charges to US destinations only, or the applicable dollar amount shown for the Product i the table above. SUMMIT ELECTRONICS LLC will not make return shipments o 2 PO Box. For shipping o international addresses, actual freight wil be charged to Customer. Return your Product freight-prepaid i ts orginal packaging, or packaging that afords an equal measure of protection. lease allow 4 to 6 weeks fr the processing of your clim (6 to 8 weeks from November to February)

$7.99
Alarm Clocks, Portable CD Players, Radios, Corded Telephones, MP3 Players, Digital Photo Frames (screen size less than 5″)| $7.99
Portable Stereo Systems, Speaker Systems, Cordless Telephones, Home DVD Players| $14.99
Home Theater DVD Systems, Portable DVD Players, Portable Media Players, Digital Photo Frames (screen sizes 5″ to 11″)| $14.99

You must email SUMMIT ELECTRONICS LLC Technical Support prior to making a return.Please ask if you are unsure of which category your product falls under.

‘US destinations only.

You must email SUMMIT ELECTRONICS LLC Technical Support prior to making a return Please ask if you are unsure of which category your product falls under. *US destinations only.

Customer Service
Servicio al Cliente
To get the best after-sales service, access the Contact
webpage from the link: https://summitcegroup.com/pages/contact.
Or email us at support@summitcegroup.com for return information and customer support! Para obtener el mejor servicio postventa, acceda a la pagina web
de contacto desde el enlace: https://summitcegroup.com/pages/contact. i0 envienos un correo electrénico a support@summitcegroup.com para obtener informacién sobre devoluciones y atencion al cliente!
For more information, please vis Para mayor informacidn por favor visite:
https://summitcegroup.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>