VOLLRATH VOL-15103 InstaSlice Pusher Head Replacement Instruction Manual

: June 13, 2024
: VOLLRATH

Table of Contents

VOLLRATH VOL-15103 InstaSlice Pusher Head Replacement
Product Information
Product Usage Instructions
SAFETY PRECAUTIONS
INSTALLATION PROCEDURES
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH VOL-15103 InstaSlice Pusher Head Replacement

VOLLRATH-VOL-15103-InstaSlice-Pusher-Head-Replacement-
product

Product Information

The product is the InstaSliceTM, a slicing equipment that is designed for safe and efficient food preparation. It consists of a blade assembly, a pusher head assembly, guide rods, and thumb screws. The pusher head assembly is responsible for pushing the food items towards the blades for slicing. The equipment also includes a guard to ensure user safety during operation.

Product Usage Instructions

Ensure that you have read and understood all the safety precautions mentioned in the user manual.
Pusher Head Replacement:
- Before performing any maintenance or replacement, make sure the equipment is turned off and unplugged.
- Remove the blade assembly by loosening the thumb screws and carefully sliding it out.
- Remove the guard by removing the thumb screws.
- Rotate the pusher head and slide it out through the provided slot. Discard the old pusher head assembly.
- Clean the new pusher head assembly with hot, soapy water. Rinse thoroughly and allow it to air dry.
- Slide the new pusher head handle first into the slot and rotate it in the operating direction.
- Install the guide rods by sliding them through the bumpers and pusher head.
- Secure the guide rods using the nylock nuts.
- Lubricate the sliding parts with mineral oil or Petro Gel. Do not use cooking oil.
- Slide the pusher head back and forth on the guide rods to ensure smooth movement.
- Slide the pusher head away from the slicing area.
- Install the blade assembly and secure it with the thumb screws.
- Slowly slide the pusher head towards the blade assembly, paying close attention to any contact between the pusher head and blades.
Pusher Finger Adjustment:
- If the pusher head slides through the blade assembly without making contact with the blades, reinstall the guard and secure it with the thumb screws. The equipment is now ready to use.
- If the pusher head makes contact with the blades, adjustment of the pusher fingers is required.
- Note which pusher finger(s) are making contact with the blades.
- Hold a thin flat tool on the pusher finger(s) that require adjustment and tap it with a mallet or similar tool. Take caution not to disrupt or make contact with another finger or scratch the anodized surface of the pusher fingers.

Please refer to the product user manual for additional information and safety guidelines.

SAFETY PRECAUTIONS

To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.
WARNING
Waming is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

WARNING Sharp Blade Hazard.
Blades are sharp and can cause cuts and amputation. To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.

INSTALLATION PROCEDURES

Slide the pusher head assembly (A) out and away from the blade assembly (D).See Figure 1
- Figure 1. Blade Assembly and Guard Removal and Installation
Loosen the thumb screws B and C) and carefully remove the blade assembly (D).
Remove the thumb screws (C and E) and the guard (F).
- Figure 2. Guide Rod, Nylock Nut and Washer Removal and Installation
Hold guide the rods (D) using a wrench on the flats (B) and remove the nylock nuts (A). See Figure 2.
Note the position and location of the washers (C) and orientation of the pusher head assembly (E). Slowly remove the guide rods (D) and washers (C).
Retain the nylock nuts (A) for reuse. Retain the washers (C) if they are going to be reused or discard if they are going to be replaced.
- Figure 3. Pusher Head Assembly Removal
Rotate the pusher head (A) and remove by sliding out through slot (B). See Figure 3. Discard the old pusher head assembly.
Thoroughly wash the new pusher head assembly with hot and soapy water. Rinse thoroughly and allow to completely air dry. Use caution not to bend or damage the pusher fingers.
Slide the new pusher head (A) handle first into the slot (B) and rotate until it in the operating direction. See Figure 4.
- Figure 4. Installation of Pusher Head
Install the guide rods (D) by sliding through bumpers (C) and pusher head (E) as shown in figure 2.
Secure the guide rods (D) using the nylock nuts (A) removed earlier.
Lubricate sliding parts with mineral oil or Petro Gel. Do not use cooking oil as it will become sticky and may permanently damage the equipment.
Slide the pusher head back and forth on the guide rods.
Slide the pusher head away from the slicing area.
Install the blade assembly (D) securing with thumb screws (B and C). See Figure 1.
Slowly slide the pusher head toward the blade assembly paying close attention to any blade and pusher head contact.

if the pusher head (A) slides through the blade assembly (D) without making contact with the blades:

Reinstall the guard (F) securing with thumb screws (C and E). Your

Insta Slice ™M is now ready to use. See Figure 1. If the pusher head (A) makes contact with the blades it will be necessary to change the position of the pusher fingers by:

Note which pusher finger(s) (A) are making contact (C) with the blades (B). See Figure 5. See Figure 1.
- Figure 5. Pusher Head Fingers and Blade Assembly
Hold a thin flat tool (B) on the pusher fingers) that require adjustment. Tap the tool B) with a mallet or similar tool. Use caution not to disrupt or make contact with another finger or to scratch the anodized surface of the pusher fingers. See Figure 6.
- Figure 6. Adjusting the Pusher Head Fingers
Slowly slide the pusher head toward the blade assembly paying close attention to any blade and pusher head contact. If the pusher head makes contact with the blades repeat previous steps 1 and 2.

Once the pusher head (A) slides through the blade assembly (D) without making contact with the blades: