Ustellar UT88863 RGB Flood Light User Guide
- June 13, 2024
- Ustellar
Table of Contents
Ustellar UT88863 RGB Flood Light
THANK YOU!
THANK YOU for choosing Stellar. To optimize user experience, please install and use the light according to the following instruction.
Warning
- Please check if the light and the parts are intact before installation.
- Make sure to cut off power before installation.
- Please do not place this light in corrosive conditions.
- If there is any damage to the cord, please cut off the power and stop using it im-mediately.
- Please do not retrofit the light within the warranty period.
- To ensure the light works properly, please use the voltage indicated on the packing.
- To avoid any damage to the light, please do not use chemical solvent during routine maintenance.
Specification
Model No.|
UT88863
| UT88866|
UT88867
---|---|---|---
Wattage|
25W
| 80W|
100W
Color|
RGB, Warm White
| RGB|
RGB
Input Voltage|
AC100-120V
Protection Rating|
IP66
Controlled By|
IR Remote Controller
Battery for Controller|
CR2032/CR202550/60Hz
Frequency|
50/60Hz
Mercury Content|
No
Lifespan
Working Temperature|
SOOOOH
-20-c-40·c
Components
Note: 1. Different plugs for different countries. 2. Cord – type Z attachment. For type Z attachment, if the external cord of this luminaire is damaged, it cannot be replaced without breaking or destroying the luminaire.
Dimension
Weight: 1.llb/0.Skg Max Projected Area:20 m’ Suggested Height for
Installation: Sm
Weight: 3.31b/1.5kg Max Projected Area:40 m’ Suggested Height for
Installation: 6m
Weight : 5.71b/ 2.6kg Max Projected Area:60m’ Suggested Height for
Installation: 6m
Installation
Step A: According to the spacing of two screw bits on the bracket, drill two holes on the mounting panel.
Step B: Aim the bracket at the holes and fix it with two bolts.
Step C: Adjust the lighting direction up or down as per your need and plug in to power the light on.
Step D: Remove the plastic sheet from the bottom of the remote controller so as to activate the controller.
Note:
01 Make sure that the distance between the light and the object being lit is more than 1 meter, so as to avoid high temperature caused by short distance.
Non-replaceable Light Source.
limitation of Indoor and Outdoor Use
- This light is waterproof and dampproof. It is protected against the rain, but it cannot be immersed in water.
- The mounting position of this light should be able to bear at least 10 times as heavy as the light.
- This light should be used in condition that is good for heat dissipation. Its working temperature should be less than 40″C. Too high the working temperature will cause serious lumen depression and affect lifespan of the light.
Remote Controller
AUTO: Loop the modes automatically.
FLASH: Flash and strobe when adjusting to the highest speed.
Jump3: flash change between 3 colors.
Jump7: flash change between 7 colors.
Fade3: smooth change between 3 colors.
Fade 7: smooth change between 7 colors.
How to DIV colors?
This flood light is made of RGB LEDs, which means there are three colors (red/green/blue) on one LED. All lighting colors are made by changing the ratio of red, green and blue on the LED.
e.g. Red + Green = Yellow Lighting
Red+ Blue= Purple Lighting
Green+ Blue= Cyan Blue Lighting
Firstly, choose and press one button from DIY1 to DIY3 on the IR controller, for instance, the DIYl button. Secondly, press ↑ or ↓ button to increase (↑) or decrease ( ↓) the ratio of red, green and blue on the LED, so as to create different lighting colors. Then the specific DIY color lighting will be saved on t he DIYl button [the button you choose on the first step). Next time when you want to use this DIV color lighting, simply press DIYl button for a quick access.
Note:
- The remote controller has memory function, which means that it can start at your last choice on color and mode.
- The flood light is controlled by the IR remote controller. To make it work perfectly, please point the remote controller to the light and make sure there is no obstacle between the light and the remote controller for better signal response.
- After a period of usage, the remote controller might run out of battery and become insensitive or the available detraction distance may be shortened. If the remote controller is not working, you might first try to replace its battery as per instructions shown below. If the remote controller still fails to work after replacing new battery, please contact the seller for help.
E-manual
Step 1: Scan the QR code
Step 2: Click E-manual PDF file
Step 3: Read file online or download
Go paper-free, make life easier, and do something good for the environment.
Contact Us
Have some issue? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
Manufacturer: Shenzhen Ustellar Technology Ltd. (shen zhen shi you shi tuo ke ji you xian gong si ) Address: 308A, 3/F, Building A, Youth Entrepreneur Hub, Jianshe East Road, Qinghua Community, Longhua Street, Longhua District, Shenzhen, CHINA 518000
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>