VOLLRATH 4075903 Meat Grinder Chamber and Components Installation Guide

: June 13, 2024
: VOLLRATH

Table of Contents

SAFETY PRECAUTIONS
AssEmBLY PROCEDURES
DisasSEmBLY PROCEDURES
Documents / Resources

Meat Grinder Chamber and Components
Assembly and Disassembly
**Installation Instructions

**

To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.
WARNING
Waming is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

SAFETY PRECAUTIONS

WARNING
**Electrical Shock Hazard.**
Keep water and other liquids from entering the inside of the unit. Liquid inside the unit could cause an electrical shock

Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock.
Do not use unit if power cord is damaged or has been modified. Do not use an extension cord with this unit

WARNING
Sharp Blade Hazard.
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance:

AssEmBLY PROCEDURES

Tum the meat grinder off and unplug from its power source.
Thoroughly clean and dry all parts.
Ifnecessary assemble the blade shaft (B) into the worm gear (A). See Figure 1.
Inspectthe shaft washer (A) for wear. See Figure 2. Replace if necessary.
Slide the shaft washer (A) onto the worm gear shaft (B).
Slide the shaft washer (A) so that it is seated against the worm gear assembly (B) as shown. See Figure 3.
Slide the worm gear assembly (B) and the shaft washer (A) into the grinder chamber (C). Slide the worm gear shatt (D) in untilitis seated fully.
Slide the knife blade (B) so that the fiat ground edges (A) face to the outside as shown, onto the blade shaft (C). See Figure 4.
Slide the knife blade (B) onto the blade shaft (C) so that it seats completely over the square (D). See Figure 5.
Place the grinder plate (D) onto the blade shaft (A) so that the cutout (C) slides over the locating pin (B). See Figure 6.
If a sausage filler is to be used, place it between the coupling cover (A) and the grinder chamber (B). See Figure 7.
Thread the coupling cover (A) onto the grinder chamber (B) and tighten securely.

DisasSEmBLY PROCEDURES

Tum the meat grinder off and unplug from its power source.
Unscrew and remove the coupling cover (A) from the grinder chamber (B). See Figure 7.
Remove the grinder plate (D) from the blade shaft (A). See Figure 6.
Carefully remove the knife blade (B) from the blade shaft (C). See Figure 5.
Remove the worm gear assembly (B) from the grinder chamber (C). See Figure 3.
Thoroughly clean and dry all parts.

The Vollrath Company, L.L.C.
www.vollrathco.com
1236 North 18t Street
Sheboygan, Wi 53081-3201
USA.
Main Tel: 800.628.0830
Fax: 800.752.5620
Technical Services: 800.628.0832
Service Fax: 920.459.5462
Canada Service: 800.695.8560
© 2010 The Vollrath Company, L.L.C.

Documents / Resources

| VOLLRATH 4075903 Meat Grinder Chamber and Components [pdf] Installation Guide
4075903 Meat Grinder Chamber and Components, 4075903, Meat Grinder Chamber and Components, Chamber and Components, Components
---|---
| VOLLRATH 4075903 Meat Grinder Chamber [pdf] Installation Guide
4075903, 4075903 Meat Grinder Chamber, Meat Grinder Chamber, Grinder Chamber, Chamber