VOLLRATH 075905 Meat Grinder Chamber and Components Instruction Manual

VOLLRATH 075905 Meat Grinder Chamber and Components Instruction Manual

To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.

WARNING
Warning is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

Safety Precautions

WARNING

Electrical Shock Hazard.
Keep water and other liquids from entering the inside of the unit. Liquid inside the unit could cause an electrical shock.

Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock.
Do not use unit if power cord is damaged or has been modified. Do not use an extension cord with this unit.

WARNING

Sharp Blade Hazard.
Blades are sharp and can cause cuts and amputation.

To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.

Assembly Procedures

1. Turn the meat grinder off and unplug from its power source.

2. Thoroughly clean and dry all parts.

3. If necessary assemble the blade shaft (B) into the worm gear (A). See Figure 1
   Figure 1. Blade Shaft and Worm Gear
   

4. Inspect the shaft washer (A) for wear. See Figure 2. Replace if necessary
   Figure 2. Shaft Washer and Worm Gear Shaft
   

5. Slide the shaft washer (A) onto the worm gear shaft (B).

6. Slide the shaft washer (A) so that it is seated against the worm gear assembly (B) as shown. See Figure 3.
   Figure 3. Shaft Washer, Worm Gear Assembly and Grinder Chamber
   

7. Slide the worm gear assembly (B) and the shaft washer (A) into the grinder chamber (C). Slide the worm gear shaft (D) in until it is seated fully.

8. Slide the knife blade (B) so that the flat ground edges (A) face to the outside as shown, onto the blade shaft (C). See Figure 4
   Figure 4. Knife Blade and Blade Shaft
   

9. Slide the knife blade (B) onto the blade shaft (C) so that it seats completely over the square (D). See Figure 5.
   Figure 5. Knife Blade and Blade Shaft
   

10. Place the grinder plate (D) onto the blade shaft (A) so that the cutout (C) slides over the locating pin (B). See Figure 6.
    Figure 6. Grinder Plate, Cutout, Locating Pin and Blade Shaft
    

11. If a sausage filler is to be used, place it between the coupling cover (A) and the grinder chamber (B). See Figure 7.
    Figure 7. Coupling Cover and Grinder Chamber
    

12. Thread the coupling cover (A) onto the grinder chamber (B) and tighten securely

Disassembly Procedures

1. Turn the meat grinder off and unplug from its power source.
2. Unscrew and remove the coupling cover (A) from the grinder chamber (B). SeeFigure 7.
3. Remove the grinder plate (D) from the blade shaft (A). See Figure 6.
4. Carefully remove the knife blade (B) from the blade shaft (C). See Figure 5.
5. Remove the worm gear assembly (B) from the grinder chamber (C). See Figure 3.
6. Thoroughly clean and dry all parts.

The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.

Main Tel: 800.628.0830
Fax: 800.752.5620

Technical Services: 800.628.0832
Service Fax: 920.459.5462
Canada Service: 800.695.8560

© 2010 The Vollrath Company, L.L.C.

References

• Commercial Foodservice & Kitchen Equipment | Vollrath Foodservice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>