B-Tech BTV510 Universal Flat Screen Wall Mount Instruction Manual

BIV5 10
FLAT SGREEN WALL MOUNT
INSTALLATION GUIDE & PARTS LIST
This Pack Contains 1 Mount

BTV510 Universal Flat Screen Wall Mount

• Suitable for screens up to 55″ (140cm) / 50kg
• Mounts screen only 20mm from wall
• Suitable for concrete, brick or stud walls up to 16″
• Includes locking bar for secure installation
• Post-installation screen alignment
• Simple ‘hook-on’ installation with all mounting hardware included
•  Max. Distance between fixings: H. 425mm x V. 400mm
• VESA® compatibility: 75 x 75, 100 x 100, 200 x 100, 200 x 200, 300 x 200, 300 x 300, 400 x 200, 400 x 300 and 400 x 400mm

Registered Design Number: 001713280-0021

TOOLS REQUIRED

INSTALLATION SAFETY INSTRUCTIONS

CAUTION
This wall mount is intended for use only with the maximum weights indicated. Use with flat screens heavier than the maximum indicated may result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference.
B-Tech International Design & Manufacturing Ltd, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech International Design & Manufacturing Ltd recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped. If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you.
Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter. Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Some walls are not suitable for installation. If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling. If you install this product on drywall it must be securely fixed to a wooden stud, concrete block or other permanent structure behind the drywall board. Installing on drywall boards alone will not support the weight of most AV equipment. When drilling holes in walls it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all wall fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualified person.

1. Attach wall plate to either a concrete or stud wall.
2. Attach interface arms.
3. Hook mount onto wall plate.
4. Lateral adjustment.
5. Insert locking bar.

PARTS LIST

PLEASE KKEP THIS PARTS LIST FOR FUTURE REFERENCE

FIXING KIT
A1| M8 X 50mm COACH SCREW| 3
A2| M8 METAL WASHER| 3
A3| NO.10 WALL PLUG| 3

Suitable for loads up to 50Kg (110lbs)

©2018 B-Tech International Design & Manufacturing Ltd. All rights reserved. B-Tech AV Mounts is a division of B-Tech International Design & Manufacturing Ltd. B-Tech, Better By Design & Ventry are registered trademarks of B-Tech International Design & Manufacturing Ltd. All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E & OE.

B-TEGH AV MOUNTS
HEAD OFFICE
Bennett House, Long March, Daventry,
Northants., NN11 4NR, UK
info@btechavmounts.com
www.btechavmounts.com
AMA-BTV510-V2-BTVBX-1118-03
Made in P.R.C.

Documents / Resources

| B-Tech BTV510 Universal Flat Screen Wall Mount [pdf] Instruction Manual
BTV510 Universal Flat Screen Wall Mount, BTV510, Universal Flat Screen Wall Mount, Flat Screen Wall Mount, Screen Wall Mount, Wall Mount
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>