GOLFZON GZ-GWPS-22 Portable Golfsensor-IR User Manual
- June 12, 2024
- GOLFZON
Table of Contents
GOLFZON GZ-GWPS-22 Portable Golfsensor-IR
Product Information
The Portable Golfsensor_IR is a golf sensing device that measures the speed and direction of the ball rolling when it is hit with a putter. It connects to other devices via Bluetooth communication and is powered by a USB cable. The hardware versionis IR-PUTT V0.9 and the software version is Wave-P1-221128.
Product Configuration and Specification
- Product Contents: Portable Golfsensor_IR (GZ-GWPS-22), USB Cable
- Category: Golf Sensor
- Product Name: WAVE PUTT
- Hardware Version: IR-PUTT V0.9
- Software Version: Wave-P1-221128
- Size (Weight): 356x307x35mm (900g)
- Input Voltage: DC 5V
- Operating Temperature: -10°C to 50°C
- Communication: BLE 5.0
Component Roles and Functions
- Portable Golfsensor_IR: Putting and hitting sensing device that connects via Bluetooth communication
- USB Cable: Power connection device for Portable Golfsensor_IR (GZ-GWPS-22)
Product Usage Instructions
Product Installation
To install the Portable Golfsensor_IR (GZ-GWPS-22), follow these steps:
- Place GZ-GWPS-22 outside the range of GZ-GWRS-22 on a flat floor.
- Connect the power using the included USB cable (recommended to use 5V 100mA or more).
- After connecting GZ-GWRS-22 in WAVE Skills, connect with GZ-GWPS-22. (GZ-GWPS-22 cannot be used alone.)
- Open the WAVE Skills app and log in (Guest mode available).
- Set “Connect the device” to “Additional device to use Wave putt”.
- Connect GZ-GWPS-22.
- Enjoy practice and games at WAVE Skills.
Make sure to align the screens of GZ-GWPS-22 and GZ-GWRS-22 for proper connection.
FCC Caution
This device complies with part 15 of the FCC rules. Please follow these guidelines:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not approved by the responsible party could void the user’s authority to operate this equipment.
- The transmitter must not be co-located or operating with any other antenna or transmitter.
- The equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the body.
Product Configuration and Specification
Product Contents
Specification
Product Information
Component Roles and Functions
Product connection configurations
- WAVE PUTT is connected to WAVE RADAR via Bluetooth. (However, the WAVE RADAR and the control unit must be connected.) WAVE-P1 is a product that measures putting.
- It is a product that measures the speed and direction of the ball rolling when it is hit with a putter with the ball in the ready position.
- The principle of measuring the ball is to measure it with an IR sensor.
- This is how IR-RX recognizes when the ball passes through when the IR-TX fires a signal
WAVE P1 Indicate LED
- BT LED
- On green LED: Bluetooth connection
- Blinky green LED: Power on & Bluetooth disconnect
- Ready LED
- On green LED: Ready
Product Installation
Portable Golfsensor_IR(GZ-GWPS-22) Installation
- Place GZ-GWPS-22 outside the range of GZ-GWRS-22 as shown on the right. (Place GZ-GWPS-22 on a flat floor. Otherwise it may affect direction.)
- Connect the power using the included USB cable. (Recommend to use 5V 100mA or more.)
- After connecting GZ-GWRS-22 in WAVE Skills, connect with GZ-GWPS-22. (GZ-GWPS-22 cannot be used alone.)
- Open the WAVE Skills app and log in. (Guest mode available)
- Set Connect the device → Additional device to use → Wave putt.
- Connect GZ-GWPS-22.
- Enjoy a practice and game at WAVE Skills.
FCC
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>