TECNO CAMON 20 Pro 5G Smartphone User Manual

June 13, 2024
TECNO

TECNO CAMON 20 Pro 5G Smartphone User Manual
TECNO CAMON 20 Pro 5G Smartphone

Explosion diagram specification

Explosion diagram pecification

1 6.67 FHD+TM H AMOLE 2 FRONT COVER GRAPHITE FILM
3 VC 4 FRONT HOUSING
5 UP MIC RUBBER 6 PS RUBBER
7 F FLSAH HOOD 8 UP SPK RUBBER
9 MAIN PCB HEAT FILM 10 MAIN PCB SEAL FRAME
11 MAIN PCB SEAL MYLAR 12 B CAM 2M ED FOAM
13 F CAM HOLDER 14 R CAM 2M FRAME
15 R CAM 2M 16 B CAM BTB ED FOAM
17 F CAM 18 R CAM 64M ELE FOAM
19 R CAM 2M 20 MAIN PCB
21 UP SPK 22 R CAM 2M RUBBER
23 MID HOUSING 24 NFC
25 LEATHER BAT COVER 26 FLASH FPCA
27 FLASH LENS B ASM 28 R CAM 2M SMALL GLASS
29 R CAM DECO 30 R CAM 64M GLASS
31 R CAM 2M GLASS 32 FINGERPRINT
33 WHITE CABLE LINE 34 BLACK CABLE LINE
35 DOWN SPK HEAT FILM 36 MOTOR
37 MAIN FPC 38 DOWN SPK RUBBER
39 USB RUBBER 40 DOWN MIC RUBBER
41 BAT 42 SUB PCBA
43 SIDE KEY 44 DOWN SPK
45 SIDE KEY FPC 46 2.0 SCREW
47 DOWN SPK FRAME 48 3.5 SCREW
49 BATTERY COVER DECO 50 SIM HOLDER
51 MID GRAPHITE FILM

Know your phone

Know your phone

  1. Front camera.
  2. Volume + key
  3. Volume – key
  4. Power key
  5. NFC

SIM/SD card installation

  1. Power off mobile.
  2. Refer to the following picture for SIM/ SD card installation.
    SIM/SDcardinstallation

Charging the phone

You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only TECNO charger and cables. Other charger soar cables may damage the device. This will in validate your phone warranty
Charging the phone

FCC Caution

Labelling requirements.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, in clouding interference that may cause undesired operation

Information to user.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur inaparticularinstallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrectthe interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: CK8n (FCC ID: 2ADYY-CK8N) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.891W/kg and when properly worn on the body is 0.744W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna

Hi OS runs on Android
TM OS. Android is a trademark of Google LLC.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals