QSFPTEK S5300-24T4X Switch Port Ethernet User Guide
- June 13, 2024
- QSFPTEK
Table of Contents
QSFPTEK S5300-24T4X Switch Port Ethernet
Product Information
The QSFPTEK S5300-24T4X is a next-gen access switch that features 24x GE RJ45 downlinks and 4x 10GE SFP+ uplinks. It supports stacking of up to two S5300 series switches to deliver redundancy, simple management, and resilience of network capacity.
Introduction
The QSFPTEK S5300-24T4X is a next-gen access switch, features 24x GE RJ45 downlinks and 4x 10GE SFP+ . It supports stacking of up to two S5300 series switches to deliver redundancy, simple management and resilience of network capacity. We appreciate your decision to select S5300-24T4X. This manual is intended to help you become acquainted with the switch design a nd provide instructions for implementing the switches into your network.
Accessories
Hardware Overview
Front Panel Ports
| Ports | Description |
|---|---|
| SFP+ | SFP+ ports for 1G/10G connection |
| RJ45 | 100/1000BASE-T ports for Ethernet connection |
| Console port | A baud rate of 9600bps, RJ45 interface |
Front Panel LEDs
| Abbrev. | Name | Description |
|---|
PWR
| ****
Power indicator
| When the switch is powered on, the indicator is on.
SYS
| ****
System indicator
| When the indicator is always on, the system is being started up.
When the indicator flickers, the system works well.
LINK/ACT
| ****
indicators of each port
| When the link on the port is normal, the indicator is always on.
When the link on the port is failed, the indicator is off.
Back Panel
| Abbrev | Name | Description |
|---|---|---|
| Grounding column | The grounding column | The grounding column must be |
fine.
POWER| AC power supply| Input voltage: AC100~240V
Installation Requirements
Tools Preparation
- Screwdriver
- Static-proof wristband
- Bolt
- Ethernet cable
- Other Ethernet terminal devices
- Control terminal
Safety Principles
- Keep dustless and clean during or after the installation.
- Put the cover at the safe place.
- Put tools at the right place where they are not easily falling down.
- Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
- Put on the protective glasses if the environment may cause damage to your eyes. Avoid incorrect operations that may cause damage to human or devices.
Site Environment
- Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged .
- Avoid to damage devices by following the electrostatic discharge prevention procedure. S5300-24T4X Hardware Installation Manual.
- Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed.
Mounting the Switch
Connecting the Power
- Plug the AC power cord to the switch power port on the back rear.
- Connect the other end of the power cord to a AC power source equipment.
Connecting the RJ45 Ports
- Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
- Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Ports
- Insert the SFP+ module into the SFP+ port.
- Plug a fiber patch cable to the SFP+ transceiver.
- Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the Management Ports
Connecting the Console Port
- Prepare an console cable.
- Insert the RJ45 connector of the console cable into the console port on the switch.
- Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.
Configuring the Switch
Configuring the Switch Using the Web-based Interface
- Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
- Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any number from 2 to 254) and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.1 in the address
bar. Enter the default username and password (admin/admin).Step 4: Click sign-
in to access the web-based configuration page.
Configuring the Switch Using the Console Port
- Step 1 : Use the console cable to direct connect the switch console port to your computer.
- Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
- Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.
- Step 4: Enter the default username and password (admin/admin).
Troubleshooting
Hardware Fault Analysis
Power and cooling systems—power and fan Port, cable and connection—ports on
the front panel of the switch and the cables connecting these ports
Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:
- When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
- if the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3
“Requirements for Common Locations”.
If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:
- If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
- If the power on-off is at the “ON” location, check the power source and the power cable.
- If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.
Support and Other Resources
- Contact us https://www.qsfptek.com/company/contact-us.html
- Email sales@qsfptek.com
- Customer Success https://www.qsfptek.com/resources/customer-success-stories
Product Warranty
- S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or exchange of your items within 14 days of receiving them.
- For more details about applying qualifications, please live chat or email salesqsfptek.com for support.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>