QSFPTEK S5300-24S8T6X 24 Port Gigabit Ethernet L3 Switch User Guide

S5300-24S8T6X Quick Start Guide
24-Port Gigabit Ethernet L3 Switch
24x GE SFP and 8x GE RJ45 Ports, with 6x 10GE SFP+ Uplink, Support Stacking
Quick Start Guide

Introduction

The S5300-24S8T6X is a next-gen fiber optic Ethernet switch, features 24x GE SFP and 8x GE RJ45 downlinks and 6x 10GE SFP+ uplinks. It supports stacking of up to eight switches, making them logically regarded as one switch for interconnection and management.
We appreciate your decision to select S5300-24S8T6X. This manual is intended to help you become acquainted with the switch desi gn and provide instructions for implementing the switches into your network.

Accessories

Hardware Overview

Front Panel Ports

Front Panel LEDs

Back Panel

Installation Requirements

Tools Preparation

• Screwdriver
• Static-proof wristband
• Bolt
• Ethernet cable
• Other Ethernet terminal devices
• Control terminal

Safety Principles

• Keep dustless and clean during or after the installation.
• Put the cover at the safe place.
• Put tools at the right place where they are not easily falling down.
• Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
• Put on the protective glasses if the environment may cause damage to your eyes. Avoid incorrect operations that may cause damage to human or devices.

Site Environment

• Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged .
• Avoid to damage devices by following the electrostatic discharge prevention procedure. S5300-24S8T6X Hardware Installation Manual.
• Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed.

Mounting the Switch

Connecting the Power

1. Plug the AC power cord to the switch power port on the back rear.
2. Connect the other end of the power cord to a AC power source equipment.

Connecting the RJ45 Ports

1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
2. Connect the other end of the Ethernet cable to the switch RJ45 port.

1. Connect SFP modules through the fiber to other Ethernet terminal devices.
2. Connect the other end of the cable to the SFP port on the front of the switch.

Connecting the SFP+ Ports

1. Insert the SFP+ module into the SFP+ port.
2. Plug a fiber patch cable to the SFP+ transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.

Connecting the Management Ports

Connecting the Console Port

1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.

Configuring the Switch

Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any number from 2 to 254) and the subnet mask to

Step 3: Open a web browser and type http://192.168.0.1 in the address bar. Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2 : Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.

Troubleshooting

Hardware Fault Analysis
Power and cooling systems—power and fan Port, cable and connection—ports on the front panel of the switch and the cables connecting these ports
Faults Relative with Power and Cooling System
Do the following checkups to help remove the fault:

1. When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
2. if the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 “Requirements for Common Locations”.
3. If the switch cannot be started and the PWR indicator is off, check the power.

Faults Relative with Port, Cable and Connection
Do the following checkups to help remove the fault:

1. If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
2. If the power on-off is at the “ON” location, check the power source and the power cable.
3. If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.

Support and Other Resources

• Contact us https://www.qsfptek.com/company/contact-us.html
• Email sales@qsfptek.com
• Customer Success https://www.qsfptek.com/resources/customer-success-stories

Product Warranty

S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or exchange of your items within 14 days of receiving them.
For more details about applying qualifications, please live chat or email sales@qsfptek.com for support.

5 Year Warranty
14-day Return Window

www.qsfptek.com
v1.0

Documents / Resources

| QSFPTEK S5300-24S8T6X 24 Port Gigabit Ethernet L3 Switch [pdf] User Guide
S5300-24S8T6X, S5300-24S8T6X 24 Port Gigabit Ethernet L3 Switch, 24 Port Gigabit Ethernet L3 Switch, Gigabit Ethernet L3 Switch, Ethernet L3 Switch, L3 Switch, Switch
---|---

References

• QSFPTEK - Compatible Optical Transceivers Factory Outlet
• Customer Success Stories - QSFPTEK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>