Supreme BA404 MASTER AIR HAND DRYER Installation Guide

Supreme BA404 MASTER AIR HAND DRYER Installation Guide

Planning

We suggest that one hand dryer be installed for every two hand basins.

The Master Air hand dryer should NOT be installed over bench tops or

reflective surfaces.

When positioning dryers take note of traffic flows in the washroom, also be aware of obstructing doors, cabinets etc.

Electrical Connection

Installation must be carried out by a qualified person in accordance with all local wiring regulations.
Fixed wiring is recommended for all installations. Wiring should emerge from the wall in the position marked on the mounting diagram.
A fixed wiring should incorporate a switch or breaker with a contact separation of at least 3mm in all poles.
Installation may be permitted in area 2 and 3 due to class II and IP23 rating as long as the whole electrical circuit is protected by an earth leakage breaker with a maximum sensitivity of 30ma.

Installation Instructions

NOTE: Dryer should not be installed within 500mm of a bench top or

reflective surface.

1. Remove cover by firstly loosening the two screws at top of cover using allen key

2. Pull top of cover away from back plate and push down and out to remove.

3. Pass power supply cable through hole in backPosition back plate on wall as per mounting diagram and securely fasten

4. After terminating cable replace the cover and test

5. The sensor sensitivity should be adjusted as required by turning the trim pot at base of Turning anti-clockwise to increase sensitivity (range), clockwise to decrease (less range).

Height recommendations

Maintenance Instructions

Very little maintenance is required to keep your hand dryer in first class operating order. However, thefollowing maintenance should be carried out six monthly in high traffic areas and twelve monthly in normal traffic areas.

1. Disconnect power supply and remove cover
2. Carefully clean lint from inside the dryer
3. Wash cover in warm soapy water to remove grime

Your guarantee could become void if the above is not performed at the specified intervals.
NOTE: If the power cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, or a suitably qualified person inorder to avoid a hazard.

Service Hints

All service work should be carried out by a qualified trades person. Turn off power supply before removing the cover. In event of your hand dryer failing to start, firstly check that the power is available, the sensor lenses are clean and sensor sensitivity has beenadjusted.

Safety Precautions & Standards Compliance

Supreme Hand Dryers have been tested and comply with all relevant Australian and New Zealand standards for electrical safety and electromagnetic interference.

CAUTION

• The dryer is not intended for use by young children or infirm persons without
• Young children should be supervised to ensure that they do not play with the
• Do not insert objects into the air outlet, doing so can behazardous and could result in electric shock.
• Do not obstruct the air inlets or outlets in any
• Do service your Hand Dryer at regular
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SUPREME COMPREHENSIVE WARRANTY

Your Supreme Hand Dryer is fully guaranteed against defective materials and faulty workmanship commencing from the date of sale (according to SPL’s records), subject to it being installed and maintained in accordance with the manufacturer’s instructions.
SPL (2021) Limited warrants that should any part of the dryer fail within the given warranty period (2- 5 years product dependant), it will be remedied by
SPL. The dryer should be returned to SPL (2021) Limited for all warranty claims. The cost of cartage will be payable by the customer.
This warranty excludes:

• Incorrect installation, or installation that does not specifically follow the installation guidelines
• Failure to follow manufacturer’s maintenance
• Damage/Failure resulting from:
  • the use of non-authorised parts
  • authorised parts not installed in accordance with the manufacturer’s instructions
  • accidental damage, negligent use, misuse, vandalism, neglect
  • damage caused either directly or indirectly by external sources – power outages, power surges, incorrect power supply, natural disaster, or insect infestation
  • water ingress caused by property maintenance or flooding
  • negligent cleaning practices (water ingress, harmful chemical etc)

The above includes consequential damage to any other goods, furnishings, or property.

• Normal wear and tear and consumable parts (HEPA filters, UV C Lamps, fuses, motor brushes etc).
• This warranty does not displace any statutory warranty in relation to the dryer but any liability of SPL (2021) Limited under any statutory warranty will be limited to a replacement or repair of the dryer or payment of the cost of such replacement or repair at the sole discretion of SPL (2021)

Note: Our Warranty only extends to products purchased and installed in New Zealand.

Read More About This Manual & Download PDF:

References

• SPL Washrooms - Hand Dryers, Sensor Taps, Baby Change Tables

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>