Supreme DIAMOND V Hand Dryer Instruction Manual

Supreme DIAMOND V Hand Dryer

General Safety Information

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

• Failure to disconnect the power source before installation can result in serious injury or death from electric shock. Always disconnect the power source before servicing or installing the hand dryer.
• Fixed wiring is recommended for all installations. Wiring should emerge from the wall in the position marked on the mounting diagram. All fi xed wiring should incorporate a switch or breaker with a contract separation of at least 3mm in all poles.
• SPL (2021) Ltd accepts no responsibility for any damage or injury to property or persons caused by improper, incorrect or unreasonable use or installation.
• Failure to properly ground this unit could result in severe electrical shock and/or death. This hand dryer must be properly grounded (Earthed) for safe operation. An identifi ed ground connection point is supplied on the chassis of the hand dryer. We recommend GFCI protection in wet or damp locations or as required by local code.
• Risk of fi re, personal injury or property damage are possible if local codes, or safety recommendations are not followed. Installation must be carried out by a qualifi ed person in accordance with all local wiring regulations.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a hazard.
• The instructions contained within the Mounting Template must be followed carefully when installing this unit. Failure to accurately follow the instructions may result in the incorrect operation of this unit, damage to property and/or personal injury.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Do not insert objects into the air outlet, doing so can be hazardous and could result in electric shock.
• Do not obstruct the air inlets or outlets in any way.
• Do service your hand dryer at regular intervals.

Operating Instruction and Parts Manual

Please read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage. Retain instructions for future reference. Supreme DIAMOND-V Hand Dryer

Description

The Supreme DIAMOND-V hand dryer is a surfaced-mounted dryer, powered by a brushless DC motor, which delivers up to 760 watts of drying power. Incorporated with a switchable 500W integrated heating element and infrared sensor with blue light assist for automatic activation. These models are intended for use in commercial, office and public facility environments.

Specifications

Recommended Mounting Heights

From Floor to Dryer Bottom Edge:

• Men’s washroom 1100mm
• Ladies’ washroom 1050mm
• Children’s washroom 13-17yr 1000mm
• Children’s washroom 10-13yrs 950mm
• Children’s washroom 7-10yrs 900mm
• Children’s washroom 4-7yrs 800mm
• Disabled Person’s 950mm

Planning

We suggest that one hand dryer be installed for every two hand basins.

NOTE: Dryer should not be installed within 600mm of a bench top or reflective surface.

Installation Instructions

1. Disconnect the power source.
2. Place the main cover on a cloth to avoid marking its surface.
3. Use the security hex key supplied to remove two security screws from the dryer, then lift cover off the main body. (Image 5)
4. To position, use the template provided to mark locations of four fixing points. Do not use the backplate as a guide for drilling. Ensure there is a 600mm clearance from surface below.
5. Pre-drill the wall in the marked locations using a 5/16 (8mm) drill, insert the plastic anchors and tap flush to the wall. (Image 1)
6. Secure the backplate to the wall with appropriate fittings (Image 2)
7. To install power cable and connection to the terminal block pull the cable through the grommet. Ensure the cable is long enough to route correctly through the backplate to the terminal block. All automatic dryers must have their own dedicated 10-amp circuit.
8. The cable must sit in the dedicated channel.
9. As shown, connect cable to terminal block (Image 3) and screw in to terminal block.
10. Fix the cable clamp with screw in the backplate. CAUTION: Connect the earthing wire to the terminal block marked
11. Set heater switch ON/OFF (Factory default setting “ON”) (Image 4)
12. Attach main body by positioning the cover over the backplate.
13. Insert and tighten the security screws into the top and bottom of the main body with the hex key (Image 5).
14. Turn unit on and test operation.
15. Handover security hex key to property manager

Maintenance and Cleaning Instructions

Regularly clean the outer casing using a soft, damp cloth to gently wipe away dirt. DO NOT use abrasives or chemicals.

Periodically deep clean:

1. Disconnect power source.
2. Use hex key provided to remove two security screws.
3. Clean all dust and lint from the interior.
4. Replace cover and tighten security screws until snug. Do not over-tighten.
5. Wipe with a damp cloth.
6. Liven dryer and test operation

Troubleshooting

and locate switch, set to ‘ON”.
Element needs replacing.| Replacement element part number – DDV200.
Dryer fails to start.| Sensor obstruction.| 1. Check sensor lens for foreign material or dirt. Clean lens with soft damp cloth and mild cleaning agent.
2. If lens is damaged or scratched, replace it. Part number DDHV207.
Faulty motor.| If relay “click” is heard, but unit does not start, replace the motor / fan assembly. Part number DDHV707.
The motor will start and slow down, then speed up.| Defective PCB.| Replace PCB. Part number DDV500.

Supreme Hand Dryer Limited Warranty

Your Supreme hand dryer is fully guaranteed against defective materials and faulty workmanship commencing from the date of sale (according to SPL’s records), subject to it being installed and maintained in accordance with the manufacturer’s instructions. SPL (2021) Limited warrants that should any part of the dryer fail within the given warranty period (2- 5 years product dependant), it will be remedied by SPL. The dryer should be returned to SPL (2021) Limited for all warranty claims. The cost of cartage will be payable by the customer.

This warranty excludes:

• Incorrect installation, or installation that does not specifically follow the installation guidelines supplied
• Failure to follow the manufacturer’s maintenance instructions
• Damage/Failure resulting from:
  • the use of non-authorised parts
  • authorised parts not installed in accordance with the manufacturer’s instructions
  • accidental damage, negligent use, misuse, vandalism, neglect
  • damage caused either directly or indirectly by external sources (power outages, power surges, incorrect power supply, natural disaster, or insect infestation)
• Water ingress caused by property maintenance or flooding
• Negligent cleaning practices (water ingress, harmful chemicals etc) The above includes consequential damage to any other goods, furnishings, or property.
• Normal wear and tear and consumable parts (HEPA filters, UV-C lamps, fuses, motor brushes etc)
• This warranty does not displace any statutory warranty in relation to the dryer but any liability of SPL (2021) Limited under any statutory warranty will be limited to a replacement or repair of the dryer or payment of the cost of such replacement or repair at the sole discretion of SPL (2021) Limited

Contact

• SPL Limited
• PO Box 437, Cambridge 3450
• New Zealand
• p. +64 7 823 5790
• e. office@splwashrooms.co.nz
• splwashrooms.co.nz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>