saxby lighting 39237 Omega Shaver Mirror Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
39237 Omega Shaver Mirror
Instruction Manual
Instruction leaflet
Omega Mirror
39237
39237 Omega Shaver Mirror
Thank you for purchasing this light fitting. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this
product. Please retain these instructions for future reference .
Warning
This is a Class 1 product and must be earthed
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
This product is not suitable for dimming.
This product is rated at IP44.
This product contains a demister pad. If this pad is damaged in anyway then it
should be replaced by a qualified electrician.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Caution: To avoid interference, the sensor must be placed a minimum of
200mm away form any surface of object.
Specification
Voltage: 220-240V~ 50Hz
Lamp: 2 x 1.5W LED module (SMD), 6500K
IP rating: 44
Shaver socket: 115V-240V dual socket
Layout
- Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting.
- Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
- Cables in walls must be protected using suitable conduit or plastic trucking.
- The mains supply cable must have a minimum cross sectional area of 1.0mm ².
- This product has special protection against the ingress of moisture and is IP44 rated.
This product is suitable for use in zone 1, zone 2 and outside zones of a
bathroom only. Please see diagram.
If this unit is being fitted in a room containing a bath or shower, a 30mA RCD
must be used – in accordance with IEE regulations.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires
- Undo the screws holding the front mirror assembly in place and set aside.
- Hold the back plate in place and mark the position of the holes. Ensure that the product is level.
- Ensure the wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
- Pierce grommet and pass the supply cable through the hole in the wall back.
- Fix the product into position.
Wiring
Having correctly identified the wiring from your existing light fitting,
pull the wire through the hole and connect to the connection block inside the
product in the following way: 
Check that…
- You have correctly identified the wires
- The connections are tight
- No loose strands have been left out of the connection block.
Commissioning
- Push the labelled male and female connectors together to power the demister pad.
- Refit the mirror front onto the wall back. Ensure that the seals are correctly located before securing.
- To attach the shelf, undo the two plastic screws underneath the bosses. Slot shelty in fully and carefully retighten the screws so the shelf is gripped firmly.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
- Activate your new LED mirror by swiping your hand in front of the sensor.
Shaver Socket Instructions
- The shaver socket is powered by a 20W isolating transformer and is only intended for use with electric shavers, electric toothbrush chargers and similar products.
- Any appliance connected to the socket must not exceed the 20W power output as this could cause damage and overheating to occur.
- Always check your appliance instructions to ensure the power requirements are less than 20W.
Demister Operation
- Simply turn on the demister switch on the side. The demister pad will warm the mirror surface.
- The demisting effect will spread approximately 10 – 20% further than the pad itself .
- We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
- Mirror – Use a damp cloth or a propriety glass cleaner. Do not use abrasive materials as these will damage the finish .
Recycling advice
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice .
Safety information
Live Voltages may be present in this unit even when turned of or when
completely disconnected. For your safety, always switch off the power supply
before changing lightbulbs, or cleaning.
The mirror must be replaced immediately should it become cracked or damaged.
This fitting must not be used without the mirror in place.
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilllantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
Saxby Lighting
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>