Saxby Lighting G5503177 Palermo 4lt Bar Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

Saxby Lighting G5503177 Palermo 4lt Bar
Product Information
Product Usage Instructions
Specification
Layout
Installation
Wiring
Check that
Commissioning
Fitting/replacing bulbs
Recycling advice
Safety information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Saxby Lighting G5503177 Palermo 4lt Bar

Saxby-Lighting-G5503177-Palermo-4lt-Bar-FIG-1

Product Information

The product is a Palermo 4 Bar Spotlight with the model number G5503177. It uses 50W GU10 Mains Halogen bulbs.
The product is manufactured by Brilliant AG, located at Brilliantstrasse 1, D-27442 Gnarrenburg, and the UK manufacturer is BH17 7BY.
The product is designed to operate with a power supply of 220-240V~ at a frequency of 50Hz. It is a Class 1 product and must be earthed for safety.

Product Usage Instructions

Before performing any maintenance on the product, always switch off the power supply to ensure safety.
To fit or replace bulbs, follow these steps:
Switch off the power supply.
Carefully remove the existing bulb(s) from the spotlight.
Insert the new 50W GU10 Mains Halogen bulb(s) into the spotlight.
Ensure the bulb(s) are securely fitted.
For installation, follow these steps:
Carefully note the position of each set of wires.
Check that the supply, neutral, earth (green/yellow), and switched live wires are correctly connected.
If necessary, use the provided 4th block for loop termination.
Connect the light fitting’s blue wire (N) to the neutral wire.
Connect the green/yellow wire to the earth wire.
Connect the brown wire (L) to the switched live wire.
For more information and support, visit the manufacturer’s website at www.saxbylighting.com.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections .
Always use the correct type and wattage bulb.
Exceeding the bulb wattage will damage the product.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
This product is suitable for dimming when used in conjunction with a dimmable lamp. Please ensure verification of dimming abilities with the lamp manufacture prior to use.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Specification

Voltage: 220-240V~ 50Hz
Lamp: 4 x Max. 50W GU10 Halogen
IP rating: 20

Layout

Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross sectional area of 1.0mm2
This product must be mounted out of arms reach.
This product has been designed with folding bars to allow different configurations and layouts to be easily achieved. To position the bars, fold them out into the desired configuration. There is no need to tighten the bars once in position.
They are designed to rotate freely to allow easy operation. When installing and using this product, take care not to allow the bars and heads to collide with each other.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires

Undo the screws (C) holding the fixing bracket in place and set aside.
Hold the bracket (A) in place and mark the position of the holes. Ensure that the product is level.
Ensure the ceiling is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. Ensure there is a joist at the point of fixing to support the weight of the product.
If the single spot is to be fitted to a wall then the correct fixings should be used for brick, cavity walls or plasterboard.
Fix into position .

Wiring

Having correctly identified the wiring from your existing the connection block inside the product in the following light fitting, pull the wire through the hole and connect to way:

Check that

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
When completed, ensure that there are no bare or loose strands of wire exposed, and cover all exposed areas of the connection block with 2 layers of insulation tape.

Commissioning

Adjust the cable so it does not get snagged.
Secure the product to the mounting bracket by locating the screws through the “I.’.’ shaped slots (C) in the ceiling cover and tightening the screws .
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Fitting/replacing bulbs

When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life.
Remove bulb by turning a quarter turn anticlockwise and pulling out.
Push the bulb gently into the lampholder and twist a quarter turn clockwise to engage pins.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish .
Glass parts – Wipe clean with a damp cloth. Do not use abrasive materials as these will damage the finish.

Recycling advice

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice .