Carvin MX1602 Professional Studio Mixer User Manual
- June 13, 2024
- CARVIN
Table of Contents
Carvin MX1602 Professional Studio Mixer User Manual
Please Read Before Operating Your Carvin Mixer
UNPACKING
Carefully remove the mixer by opening the carton and holding the carton flaps out. Turn the mixer upside down and lift the carton off. Now turn t he mixer right-side up. In the event the mixer is moved or re-shipped “ALWAYS” use the original carton and packing material. If not, structural damage could deface the unit. Carvin or the Shipping Company will not be liable. SAVE ALL PACKING MATERIALS!
INSPECTION
Inspect the unit for damage that may have occurred in transit. If damage is found, notify the transportation company immediately, and file a damage claim. The Claim must be instituted by yourself, the consignee. Save all cartons for proof of damage. Please notify Carvin of any damage done.
MIXER SET-UP – Do Not Turn On Yet!
The information supplied within this manual is intended to explain the
operation of your mixer as clearly and concisely as possible. However, no
attempt has been made to instruct an operator on the basic principles of sound
reinforcement or recording techniques. A number of looks are available on
these subjects.
TO SET-UP, develop and adhere to a standard procedure of setting all Faders to
their lowest position. Set all Channel Equalizers to the “Flat” mid-position.
Set the Graphic Equalizer (if equipped) to the center “O” mid-position. Set
Pan controls to mid-position. Turn all remaining controls fully counter-
clockwise to the off position. Now, check that the AC line voltage in your
area matches the input requirements of your board. The voltage can vary ± 10%
of rated input. Make al I the necessary connections to the Board and you
should be ready to start by following the detailed instructions of this
manual.
MIXER INTRODUCTION
Your new Carvin Mixer has been designed and built using the most modern and
innovative circuits available, in order to bring to you a state-of-the-art
professional mixer. Our constant research into audio circuitry as well as
attention to the latest methods of electronic packaging combine to produce the
basic concept of our mixer. We talked with, and received, extensive feedback
from sound contractors as well as sound people, involved with sound
reinforcement, about the real needs and requirements of a mixer before
actually beginning our design.
Even though you paid a very reasonable price for your board, it is actually
constructed better than many more expensive ones. As an example, your board is
wired with a military-type wiring harness. The steel chassis is precision
formed and assembled in a modular fashion designed to eliminate strong RF
fields. All P.C. Boards are G-10 epoxy fiberglass. Only the best of components
like – Switch craft connectors, Centrale switches, CTS sealed controls, low
noise/high slew rate Op-Amps and discrete amplifiers are used. These quality
components and our reasonable price is made possible because we sell direct to
you, eliminating retail commissions.
Your Carvin mixer is designed to give years of trouble free service. If you
have further questions, please call or write.
REAR PANEL DESCRIPTION
-
25. The MAIN OUTPUTS of A & B and Monitors 1 and 2 plus the SUM A+ B all featured Balanced D3F connectors and Unbalanced Phone jacks. These outputs are designed for a minimum impedance of 600 Ohms. Both type of outputs can be used at the same time providing that the total impedance is not below 600 Ohms.
Likewise the CONTROL ROOM Outputs and the EFFECTS SEND can be used with a minimum load impedance of 600 Ohms. -
26. The CHANNEL SEND & RECEIVE Jacks are designed for individual channel interruption tor accessories or as Direct Outs for recording.
The SEND jack is designed for any loads down to 600 Ohms for sending the channel signal to your accessory or recorder. This jack does not interrupt the signal to the main fader when used.
The CHANNEL RECEIVE jack is designed to receive your signal back into the channel. The input impedance of this jack is also 600 Ohms in which your device should be capable of delivering a signal into a 600 Ohm load. This jack interrupts the channel output to the Main Fader which enables the entire signal to go through your device before returning to the board.
NOTE: Both the CHANNEL SEND & RECEIVE are pre-fader(not affected by the fader). The Output of the SEND jack is -10dBM with a – 50dBM input reference. The 40dB amplification should be more than ample for professional recorder requirements. -
27. The AC LINE CORD is a three wire grounding type which features a European-style connector for easy removal. Use care when connecting as this can be subject to damage. For proper mixer grounding, always plug into a 3 prong grounded outlet.
-
28. The PRIMARY FUSE is designed to protect your boards power supply should there be any malfunction. The proper fuse value is 1AGC. Never use a different value or permanent damage may result to the boards power supply.
-
29. The 110-220 VOLT OPERATION SWITCH is located under the AC power socket and is covered by a protective cap. All boards are preset for 110/120 volt operate ion from the factory. Please check the power in your area. If your area is using 220 volts, please remove the cap and visually select the internal switch to 220. The wrong input voltage will damage the power supply which will not be covered under warranty.
DISASSEMBLY FOR SERVICING. All servicing can be accomplished by removing the bottom cover plate only. This is done by removing 12 screws from the bottom plate (4 from each front and back and 2 screws from each wood end piece). The plate should now lift off. To re-assemble, always put the screws back into the wood end pieces first. NOTE: Do not take the wood end pieces off as you might experience difficulty in re-aligning your board back together again. CAUTION: Do Not Cross-thread or use excessive force on the “PemNuts” that hold the screws to the metal as they can be pushed-out or damaged.
KEEPING YOUR BOARD LOOKING GOOD. The Solid Walnut ends are of fine furniture quality. To keep the hardwood from drying out, we recommend using Lemon Oil on a soft polishing cloth. Be careful not to get the oil on the panel. Also use a soft paint brush occasionally to dust your board off. If your board is dirty, dampen a soft cloth and wipe the board clean.
MX1202 and MX1602 Specifications
LIMITED WARRANTY
Your Carvin Professional Series Product is protected against failure for 1
YEAR. Carvin will service the unit, supply all parts, and pay the RETURN
shipping charges at no charge to the customer providing the unit is under
warranty. At no time will Carvin pay for Servicing or Parts except our own.
This warranty is extended to the original purchaser only (not transferable)
and does not cover failures by incorrect use, inadequate care of unit, or
natural disasters.
Carvin takes no responsibility for any horn driver or speaker damaged by this
unit.
This warranty is in lieu of all other warranties, expressed or implied, and no
representative or person is authorized to represent or assume for Carvin any
liability in connection with the sale or servicing of Carvin products.
FACTORY SERVICING
We highly recommend utilizing our specialized servicing staff to bring your
unit up to factory specifications. For Factory servicing “In” or “Out” of
Warranty follow these requirements:
- Call us TOLL-FREE 800-854-2235 for a return authorization number. Write this number on the shipping carton.
- enclose a full description of the malfunction. State whether or not the unit is under warranty.
- Return the amp in its original carton. Neither Carvin nor the Shipping Co. is liable for damage caused by improper packing. Ship by United Parcel Service if possible. The shipment must be pre-paid by the customer.
- Allow 5 working days for servicing plus shipping time to and from destination.
- Carvin will pre-pay the shipping (by United Parcel) back to you providing the unit is under warranty. If you wish return shipment by AIR, you will be required to pay the difference COD.
- If your unit is out of warranty, you will be charged a modest fee (generally lower than repair shops). You will also be required to pay the return shipping charges. These charges will be collected COD.
SERVICING IN YOUR AREA
You may select your own service center or have your qualified technician work
on the unit at your own expense. This will not void the warranty for future
repairs by us unless damage was done because of improper servicing or
components. If damage was done, a normal fee for parts and servicing will be
charged.
Under the 1 Year Warranty, Carvin will ship parts pre-paid to you or your
technician providing the defective part(s) are returned first for our
inspection.
If you do not have a qualified service person, we ask that you don’t involve
yourself in servicing the unit. By sending the unit back to us, you may save
time and money in the long run, plus your unit will be factory serviced.
Reminder: Carvin Does Not Pay for other Servicing or Parts except our own – No
Exceptions. If you elect to have your own servicing done, these bills must be
paid by you.
1155 Industrial Ave., Escondido, Calif. 92025
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>