SATCO NUVO 60/5943 Outdoor 19.5 inch Post Light Pole Lantern Instruction Manual

SATCO NUVO 60/5943 Outdoor 19.5 inch Post Light Pole Lantern

Based on the text extract from the user manual, here is the detailed product information and product usage instructions:

Product Information

• Item No: 60-5943
• Product Name: Unspecified

Installation and Safety Instructions
Please follow the below instructions for a safe installation of the product:

Group A: Connect to Black House Wire

• Black Parallel Wire (round & smooth)
• White or Grey with Tracer
• Brown, Gold, or Black without a Tracer

Group B: Connect to White House Wire

• White Parallel Wire (square & ridged)
• White or Grey without Tracer
• Brown, Gold or Black with Tracer

Note: When using parallel wire (SPT-I & SPT-2), the tracer wire is square shaped or ridged, and the less tracer wire is round in shape or smooth (seen best when viewed from the wire end.)

Product Usage Instructions

1. Step 1: Identify the black house wire and the white house wire.
2. Step 2: Connect the fixture wires from Group A to the black wire from the outlet box. Ensure that the fixture wires are evenly placed against the black wire.
3. Step 3: Do not twist the wires together before using wire connectors.
4. Step 4: Fit a wire connector over the wires and screw it clockwise until you feel firmness.

FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling that contains a radiant-type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.

INSTALLATION

STEP 1: While supporting the fixture, connect the electrical wires. If your post has a ground wire (green or bare copper), connect the fixture ground wire to it. If not, consult your electrician for proper grounding. After the wires are connected, tuck them carefully inside the post (A).
STEP 2: Place the fixture onto the pole, and secure with the 3 mounting screws (B).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2 : Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

GROUP A:

Connect to Black House Wire

| GROUP B:

Connect to White House Wire

---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from the wire end.)
STEP 3: Take your fixture wire(s) from group A and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: Take off the roof (D) from the cage (F) by loosening mounting screws (C).
STEP 2: Install Bulb (E) E26 medium base (not included). Do not exceed the maximum wattage rating.
STEP 3 : Attach the roof (D) back to the cage (F) by mounting screws (C).

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. Be sure to use exact wording from illustrations when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>