V I V O STAND-V001Q Pneumatic Arm Single Monitor Desk Mount Instruction Manual

: June 12, 2024
: V I V O

Table of Contents

STAND-V001Q Pneumatic Arm Single Monitor Desk Mount
PACKAGE CONTENTS
ASSEMBLY STEPS
Documents / Resources

Pneumatic Arm Single Monitor Desk Mount
Instruction ManualSKU: STAND-V001Q

STAND-V001Q Pneumatic Arm Single Monitor Desk Mount

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.

https://vivo-us.com/products/stand-v001q

GET IN TOUCH
Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - PACKAGE
CONTENTS

TOOLS NEEDED
Phillips Screwdriver
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1
OPTION A: Clamp Installation
Install Clamp Base Support (C) onto base of Monitor Stand (A) with M6x10mm Screws (S-B) using 4mm Allen Wrench (T-A). Apply Pads (I) to bottom of Clamp Base Support (C).
Secure Clamp (D) to upper two holes of Clamp Base Support (C) with M6x10mm Screws (S-B) using 4mm llen Wrench (T-B) for desks with a thickness of 10-55mm. (Use lower two holes with for desks with a thickness of 50-85mm)
Attach Cable Clip (E) to Clamp Base Support (C). Tighten the clamp to the desktop using hand bolt.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
1

OPTION B: Grommet Base Installation
Slide M8x105mm (S-A) through the top of the Base Support (F) and install on base of Monitor Stand (A) with M6x10mm Screws (S-B) using 4mm Allen Wrench (T-A). Apply Pads (I) to bottom of Base Support (F). Position stand on desk with M8x105mm Screw (S-A) through hole, and secure by using the Support Plate (G) and Knob (G) on underside of the mounting surface.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
2

STEP 2
Position VESA Plate (B) on back of monitor and secure with Screws (M-A or M-B) with M5 Washers (M-C).

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
3

STEP 3
Pull back latch on monitor arm, and slide monitor into place.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
4

STEP 4
If needed, adjust the bolt on the side of the hinge behind the VESA plate to tighten or loosen the tilt angle support. Adjust gas spring tension by turning screw with 6mm Allen Wrench (T-B) . Clockwise reduces tension, counter- clockwise increases tension. The tension should be just enough to hold your monitor in place without lifting itself up. NOTE:Tighten the socket set screw on the top of the gas spring adjustment screw if the joints are making a popping sound.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
5

WARNING:
Monitor must be installed on mount before making tension adjustments to the gas spring arm. Keep monitor in a straight orientation when making adjustments.
STEP 5
Remove cable covers as shown from upper and lower arms.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
6

STEP 6
Replace covers making sure the cables have enough slack to allow free movement of the arm.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
7

STEP 7
Store tools in Cable Clip (E) if clamp option is used.

V I V O STAND V001Q Pneumatic Arm Single Monitor Desk Mount - ASSEMBLY
8

** Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com**
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo- us.com

Documents / Resources

| V I V O STAND-V001Q Pneumatic Arm Single Monitor Desk Mount [pdf] Instruction Manual
STAND-V001Q, STAND-V001Q Pneumatic Arm Single Monitor Desk Mount, Pneumatic Arm Single Monitor Desk Mount, Arm Single Monitor Desk Mount, Single Monitor Desk Mount, Monitor Desk Mount, Desk Mount, Mount
---|---