saxby lighting EL-10047 Grove 4 Light Square Spotlight Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
saxby lighting EL-10047 Grove 4 Light Square Spotlight
Product Information
The 4lt Spotlight (EL-10047) is a lighting fixture manufactured by Saxby Lighting. It is designed for household use and provides focused illumination. The product comes with an instruction manual that contains safety warnings, care information, and assembly/user instructions.
Safety Warnings
- Allow the spotlight to cool for 10 minutes before replacing, adjusting, or cleaning.
Care Information
- Follow the recommended cooling time before handling the spotlight.
Manufacturer Information
- UK Manufacturer: Saxby Lighting, BH17 7BY
- EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Product Usage Instructions
Before using the 4lt Spotlight, please follow the assembly/user instructions provided in the manual.
Safety Warnings
This product is only suitable for connection to a 240V~50Hz supply in accordance with current IEE wiring Regulations and should be installed in accordance with local Building Regulations and is for Domestic indoor ceiling use only (it must be mounted out of arm reach) and is not suitable for a Bathroom location. This product should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature circuit breaker). If in doubt we recommend you contact a qualified electrician. Before installing your light fitting always: Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker before commencing installation. Ensure that no one else has access to the supply such that it could be inadvertently reconnected. Never fit bulbs of a higher wattage or of a type other than those specified on the label as this may cause overheating and damage the fitting. The spot heads, and bulbs, become hot during use so please switch off and allow 10 minutes to cool before replacing the bulb, adjusting or cleaning. This product contains glass parts – be careful during handling and maintenance to avoid breakage. Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product. The “Minimum Distance” Label on the product – typical format shown below – indicates that lighted objects should not be placed within the distance stipulated on the label. The example label below indicates that lighted objects should not be placed within 0.5m (50cm) of the spotlight to prevent them from overheating.
If any modification is made it will invalidate the warranty and may render the
product unsafe.
Care Information
Allow 10 minutes to cool before replacing, adjusting, or cleaning. Clean with
a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Assembly/ User Instructions
Before you start
Please read these instructions carefully before fitting your new spotlight and
retain it for reference. Make sure that there are no pipes or cables beneath
the mounting surface. Check the packaging and make sure that you have all the
required parts. Follow each assembly step in order to prevent incorrect
assembly. Make sure all screws/nuts, including electrical connections etc, are
fully tightened before use. This type of Light Fitting may be connected to a
Dimmer if a Tungsten incandescent bulb is used (as supplied. If a CFL/LED type
bulb is fitted then these cannot (generally) be controlled by a dimmer. The
product contains a spotlight with connection terminals.
The following tools may be required:
Selection of cross and flat-head screwdrivers.Electric drill and assorted
drill bits. Wire strippers.
- Decide on the position of the light fitting / or remove the existing light fitting. Take note of the position of the electrical connections. Ensure there is a solid mounting surface, preferably a wooden joist or joist bridge to support the weight of the light fitting.
- Diagram 1. Remove the fixing bracket by undoing the 2 side screws (1), and retain these for re-use.
- Use the fixing bracket (2) as a template to mark the screw holes, mark the screw holes, and secure them to the ceiling with the screws (3) supplied.
- Diagram 2. Support your fitting and connect the house wiring to the terminal block (4) – see wiring details. NOTE: This is a Class I fitting and must be earthed. The 4th terminal block connector shown is used for the “loop” wires of the “Ring Circuit”. There may be more than one set of cables in the “loop” connections. If there is a “Ring Circuit” and you do not understand the connections you must consult an electrician. Any loose terminal block -not secured to ceiling cup – should always be covered with 2 layers of good-quality insulation tape.
- Diagram 3. Secure the fitting back onto the fixing bracket with the 2 side screws removed in 2 above. Make sure that all the internal cables and connections are inside the ceiling cup, taking care not to trap or strain the internal cables.
- Fit the appropriate bulbs (5) into the lamp holders. NOTE; Never fit bulbs of a higher wattage than those specified on the label (as these may cause overheating and damage the fitting).
- Turn on the power and test.
- UK Manufacturer: BH17 7BY
- EU Manufacturer: Brilliant AG,
- Brilliantstrasse 1, D-27442 Gnarrenburg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>