V I V O MOUNT-PC06L Large Under Desk PC Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
Large Under Desk PC Mount
Instruction Manual
SKU: MOUNT-PC06L
MOUNT-PC06L Large Under Desk PC Mount
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/mount-pc06l
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
Remove protective film from Pads (C) and apply to Brace (B).
STEP 2
Remove the Support Bar (B1) from Brace (B) using the 3mm Allen Wrench (T-A).
Install the Support Bar (B1) and Brace (B) onto Mount (A) using the previously
removed hardware and 3mm Allen Wrench (T-A).
STEP 3
Adjust assembled mount as needed to fit your PC. This will help gauge the
space consumed by the mount when determining your desired mounting location.
DEPTH:
Loosen Set Screw (B2)
on Support Arm (B) and
slide to adjust to desired
PC depth, then retighten.| WIDTH:
Use a Phillips screwdriver to
loosen Set Screw (A1) on lower
Mount (A), then pull to adjust to
desired width and then retighten.| HEIGHT:
Pull and hold Side Pin (A2)
on Mount (A) and adjust to
desired height. Release pin
when necessary height is
reached.
INSTALLATION STEPS
INSTALLATION OPTIONS:
Choose your desired installation method and follow appropriate steps below.
Desk Mount
STEP 1
Hold Mount (A) up to desired mounting location and mark hole locations using a
pencil. When marking the keyhole locations, ensure to only mark the narrow
section of the keyhole.
STEP 2
Drill 0.4” (10mm) deep holes using a 0.125” (3.5mm) drill bit. Using a
Phillips screwdriver, partially install two ST4.8x16mm Screws (W-A) in-line
with the keyhole locations on Mount (A) leaving at least a 4mm gap. 
STEP 3
Hang Mount (A) over screws, making sure they are in the larger part of the
keyhole openings. Slide the mount toward the narrow keyhole opening to lock
into place. The screw heads should now be holding up the unit. Tighten the
screws fully and install the remaining two ST4.8x16mm Screws (W-A) using a
Phillips screwdriver. 
Wood Wall Mount
STEP 1
Hold Mount (A) up to desired mounting location and mark hole locations using a
pencil. When marking the keyhole locations, ensure to only mark the narrow
section of the keyhole. Drill 1.5” (38mm) deep holes using a 0.125” (3.5mm)
drill bit. 
STEP 2
Using a Phillips screwdriver, partially install two ST4.8x38mm Screws (W-B)
in-line with the keyhole locations on Mount (A) leaving at least a 4mm gap.
STEP 3
Hang Mount (A) over screws, making sure they are in the larger part of the
keyhole openings. Slide the mount toward the narrow keyhole opening to lock
into place. The screw heads should now be holding up the unit. Tighten the
screws and install the remaining two ST4.8x38mm Screws (W-B) using a Phillips
screwdriver. 
Concrete/Brick Wall Mount
STEP 1
Hold Mount (A) up to desired mounting location and mark hole locations using a
pencil. When marking the keyhole locations, ensure to only mark the narrow
section of the keyhole. Drill 1.5” (38mm) deep holes using a 0.25” (6mm) drill
bit. Insert Concrete Anchors (W-C) into the drilled holes. 
STEP 2
Using a Phillips screwdriver, partially install two ST4.8x38mm Screws (W-B)
in-line with the keyhole locations on Mount (A) leaving at least a 4mm gap.
STEP 3
Hang Mount (A) over screws, making sure they are in the larger part of the
keyhole openings. Slide the mount toward the narrow keyhole opening to lock
into place. The screw heads should now be holding up the unit. Tighten the
screws and install the remaining two ST4.8x38mm Screws (W-B) using a Phillips
screwdriver. 
Placing PC in Mount
ALL INSTALLATION TYPES:
Place your PC on Mount (A) and adjust the back brace and side support
locations as needed.
Use 3mm Allen Wrench (T-A) to loosen the the Support Bar (B1) on Brace (B) and
adjust the height to clear any cables protruding from the PC.
DEPTH:
Loosen Set Screw (B2)
on Support Arm (B) and
slide to adjust to desired
PC depth, then retighten.| WIDTH:
Use a Phillips screwdriver to
loosen Set Screw (A1) on lower
Mount (A), then pull to adjust to
desired width and then retighten.| HEIGHT:
Pull and hold Side Pin (A2)
on Mount (A) and adjust to
desired height. Release pin
when necessary height is
reached.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Large Under Desk PC Mount – VIVO - desk solutions, screen mounting, and more