UEi HUB2 Refrigeration Analyzer Kit Instruction Manual

June 12, 2024
UEi

HUB2 / HUB4 / HUB6

UEi HUB2 Refrigeration Analyzer Kit

INSTRUCTION MANUAL

HUB2 Refrigeration Analyzer Kit

UEi HUB2 Refrigeration Analyzer Kit - Fig 1

1-800-547-5740
www.ueitest.com • email: info@ueitest.com

HUB2
2 WHP1
4 Batteries (AAA)
Carrying case| HUB4
2 WPP1
2 WPC1
4 Batteries (AA)
Carrying case| HUB6
2 WHP1
2 WPP1
2 WPC1
8 Batteries (4x AA, 4x AAA) Carrying case
---|---|---

IMPORTANT SAFETY WARNINGS

WARNING
Read entire safety notes section regarding potential hazard and proper instructions before using these probes. In this manual the word “WARNING” is used to indicate conditions or actions that may pose physical hazards to the user. The word “CAUTION” is used to indicate conditions or actions that may damage these instrument.
WARNING
To ensure safe operation and service of these probes, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
WARNING
Maximum over pressure is: 1000 PSI.

WARNING

  • Do not open these probes to replace batteries while the probes are connected to an HVACR or other mechanical system.
  • To avoid false readings, replace batteries if a low battery indicator appears.
  • Do not use this these probes if they appear damaged.
  • Always adhere to national and local safety codes. Use proper personal protective equipment (PPE).

WARNING
These probes are designed for trade professionals who are familiar with the hazards of their trade. Observe all recommended safety procedures that include proper lockout utilization and use of personal protective equipment that includes safety glasses, gloves and flame resistant clothing.

WHP1 OVERVIEW

UEi HUB2 Refrigeration Analyzer Kit - Hygrometer

1. Hygrometer (WHP1): Hub 2 & Hub 6
A. Lock Button: Press to open or close probe
B. 1/4” diameter probe.
C. Magnetic Mount
D. Battery Cover.
E. Light: Blinks GREEN when probe is powered on. Blinks RED when low battery.*

CAUTION: Press down Lock Button to release probe. Failure to do so may break probe and is not covered under warranty.
GENERAL SPECIFICATIONS
Temperature Range: 32˚F to 140˚F (0˚C to 60˚C)
Temperature Accuracy: ±0.5˚F (0.3˚C)
Relative Humidity Range: 0% to 100%
Relative Humidity Resolution: 0.1%
Relative Humidity Accuracy: ±3% 20% to 80%
otherwise ±5%
Operating Temperature: 41°F to 140°F (5°C to 60°C)
Storage Temperature: 14°F to 140°F (-10°C to 60°C)
Operating Humidity: 20% RH to 80% RH
Recommended: Do Not use longer than 60 hours out of range
Dimensions: 6.84 in x 1.93 in x 1.53 in (17.4 cm x 4.9 cm x 3.9 cm)
Item Weight: 4.4 oz (125 gr)
Certification: CE Conformity, FCC/IC
Battery Type: (AAA) 2
Battery Life: 100+ hours

  • NOTE: Low battery indicator is also in the “Tool Connection” screen Battery level are displayed in the tool connection screen to the right of each probe connected.

Caution: Take care not to lose the screws when opening battery compartments

  • Remove battery cover.
  • Replace the old batteries with 2 new (AAA) batteries.
  • Replace the battery cover.

WPP1 OVERVIEW

2. Pressure Probe (WPP1): Hub 4 & Hub 6
A. Cable connector plug-in: for connecting the pipe clamp sensor (WPC1).
B. Battery cover
C. Light: Blinks GREEN when probe is powered on and blinks RED when low battery.*
D. Power Button: Hold for one second to power on
E. 1/4”pressure connector
F. 1/4” pass-through *connector NOTE:** Low battery indicator is in the “Tool Connection” screen

GENERAL SPECIFICATIONS
Range: 0 to 725 PSIg
Resolution: 0.1 PSI
Accuracy: 0.5% F.S. (at 25˚C ±3˚C) Total 1% F.S. 32˚F to 158˚F (0˚C to 70˚C)
Operating Temperature: 14°F to 158°F (-10°C to 70°C)
Storage Temperature: 14°F to 140°F (-10°C to 60°C)
Operating Humidity: 30% RH to 85% RH
Over-range: 1000 PSI
Dimensions: 6.70 in x 1.56 in x 1.44 in (17 cm x 4 cm x 3.7 cm)
Item Weight: 7.4 oz (210 gr)
Certification: CE Conformity, FCC/IC
Battery Type: (AA) 2
Battery Life: 100+ hours

Battery level are displayed in the tool connection screen to the right of each probe connected.

Caution: Take care not to lose the screws when opening battery compartments

  • Remove battery cover.
  • Replace the old batteries with 2 new (AA) batteries.
  • Replace the battery cover.

WPC1 OVERVIEW

3. Pipe clamp sensor (WPC1): Hub 4 & Hub 6
A. Temperature sensor
B. Cable connector plug-in: for connecting WPC1 to the WPP1.
NOTE: Maximum pipe diameter is 1.5 in. (3.8cm) GENERAL SPECIFICATIONS
Range: 32˚F to 176˚F (0˚C to 80˚C)
Resolution: 0.1˚F
Accuracy: ±(0.6˚F (0.3˚C))
Response Time: <30 sec.
Operating Temperature: -40°F to 185°F (-40°C to 85°C)
Storage Temperature: 14°F to 140°F (-10°C to 60°C)
Dimensions: 5.66 in x 3.81 in x 1.10 in (14.4 cm x 9.7 cm x 2.8 cm)
Item Weight: 2.1 oz (60 gr)
Certification: CE Conformity, FCC/IC

UEi HUB OVERVIEW

UEi HUB2 Refrigeration Analyzer Kit - Refrigerant Side

A. Suction Line Pressure
B. Suction Line Temperature
C. Refrigerant Favorites (tap to view)
D. Liquid Line Pressure
E. Liquid Line Temperature| F. Refrigerant List (tap to view)
G. Air Side Screen (tap or swipe left to view)
H. Vapor Saturation Temperature
I. Liquid Saturation Temperature
---|---

UEi HUB2 Refrigeration Analyzer Kit - Air Side

A. Refrigerant Side Screen (tap or swipe right to view)
B. Delta T
C. Target Delta T (assumes 400 CFM/ton)
D. Return Dry Bulb Temperature| E. Return Wet Bulb Temperature
F. Return and Supply Calculations (tap to view)
G. Supply Dry Bulb Temperature
H. Supply Wet Bulb Temperature
---|---

UEi HUB2 Refrigeration Analyzer Kit - Refrigerant List

R11
R113
R114
R115
R116
R12
R123
R133ZD
R1234YF
R1324ZE
R124
R125
R13
R134A
R142B
R143A
R152A
R22
R227EA
R23
R236FA
R245FA
R290
R32
R401A
R401B
R401C
R402A
R402B
R403A
R403B| R404A
R405A
R406A
R407A
R407B
R407C
R407E
R407F
R407H
R408A
R409A
R409B
R410A
R410B
R411A
R411B
R412A
R413A
R414A
R414B
(Hotshot)
R416A
R417A
R417C
(Hotshot 2)
R418A
R419A
R420A
R421A
R421B
R422A| R422B
(NU22B)
R422C
(One shot)
R422D
R423A
R424A
R425A
R426A
R427A
R428A
R429A
R430A
R431A
R432A
R433A
R434A
(RS-45)
R435A
R436A
R436B
R438A
(MU99)
R444A
R444B
R448A
R449A
R450A
R452A
R452B
R453A| R454A
R454B
R454C
R455A
R458A
R500
R501
R502
R503
R504
R507A
R508A
R508B
(Suva95)
R509A
R510A
R512A
R513A
R600
(Butane)
R600A
(Isobutane)
R601
(Pentane)
R601A
(Isobu-tane)
---|---|---|---

Refrigerant Favorites Button: displays selected favorites for quick changes.

UEi HUB2 Refrigeration Analyzer Kit - Units Screen

Tap to select or enter units
A. Pressure Units
B. Temperature Units
C. Enthalpy Units
D. Elevation
E. Units

UEi HUB2 Refrigeration Analyzer Kit - Tool Connection
Screen

A. Tool Assigned
B. Forget Tool
C. Tool found but not assigned
D. Battery Level
E. Signal Strength
F. Refresh nearby tools

UEi HUB2 Refrigeration Analyzer Kit - User Info ScreenUEi HUB2 Refrigeration Analyzer Kit - Support
Screen

A. Contacts
B. Manual (English, Spanish and French)
C. Find a distributor@UEitest.com
D. Tap to view Features + Benefits Video

FCC/IC INFORMATION

FCC and IC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC/IC RSS102 radiation exposure limits set forth for an uncontrolled environment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

FCC AND IC NOTICE
This device complies with Part 15 of the FCC rules and Industry Canada license exempt RSS 247. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION
The device must not be co-located or operated in conjunction with any other antenna or transmitter.
Caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
a. The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.
b. This device complies with RSS247 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.

DISPOSAL

Caution: This symbol indicates that equipment and its accessories shall be subject to separate collection and correct disposal.

CLEANING

Periodically clean your probe using a damp cloth. DO NOT use abrasive, flammable liquids, cleaning solvents, or strong detergents as they may damage the finish, impair safety, or affect the reliability of the structural components.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the General Specifications section, allow the instrument to return to normal operating conditions before using it.

WARRANTY

The HUB is warranted to be free from defects in materials and workmanship for a period of 1 year from the date of purchase. If within the warranty period your instrument should become inoperative from such defects, the unit will be repaired or replaced at UEi’s option. This warranty covers normal use and does not cover damage which occurs in shipment or failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper maintenance. Batteries and consequential damage resulting from failed batteries are not covered by warranty.
Any implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose, are limited to the express warranty. UEi shall not be liable for loss of use of the instrument or other incidental or consequential damages, expenses, or economic loss, or for any claim or claims for such damage, expenses or economic loss.
Warranty only covers hardware and does not extend to software applications.
A purchase receipt or other proof of original purchase date will be required before warranty repairs will be rendered. Instruments out of warranty will be repaired (when repairable) for a service charge
For more information on warranty and service, contact:

www.ueitest.com Email: info@ueitest.com
1-800-547-5740
This warranty gives you specific legal rights. You may also have other rights,
which vary from state to state.

Copyright © 2023 Kane USA Inc. All Rights Reserved. 17500 03/23

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals