saxby lighting 52485 Fixed Converse Recessed Downlight Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

Specification
Installation
Wiring
Fitting
Fitting/replacing the bulbs
Care and Cleaning
Recycling advice
Safety information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction leaflet
Fixed Converse Recessed
52485, 70417, 70418 saxby lighting 52485 Fixed Converse Recessed
Downlight

Thank you for purchasing this light fitting.
Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Please retain these instructions for future reference.

Warning
This product is Double Insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
This product is suitable for dimming when used in conjunction with a dimmable lamp. Always check dimming capability of the intended lamps.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Specification

Voltage:	220-240V 50Hz a.c.
Lamp:	1 x Max. 50W GU10
IP rating:	20

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the connector block and each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and connector block away from areas where they may be at risk from being cut. trapped or damaged
Cables that are to be in walls must be protected using suitable conduit or plastic Dunking.

Fixing sizes

65-125mm diameter cutout
150mm minimum cavity depth.

Spotlights give a concentrated beam of light and must not be positioned any closer than 0.5M (50cm) to the illuminated surface.

This product has no special protection against the ingress of moisture, and is rated as IP20.
This product is suitable for use in outside Zones of a bathroom only. See diagram.
The mains supply must be fitted to a 30mA RCD.

Installation

Ensure the mains is disconnected. Remove the existing fitting and discard.
Disconnect the wiring, and connect the chosen lamp holder for mains voltage halogen GU10
Fit the extended spring clips to the downlight and fit the downlight into the surround.
Lift the downlight into position. Feed the cable through the centre of the downlight
Wire as detailed below.

Wiring

This product is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.
Having correctly identified the wiring from your existing light fitting and connect to the connection block inside the product in the following way:

Check that…

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Fitting

Point the spring clips upwards and fit the two longer arms into the ceiling hole.
Push the unit upward until firmly in position, ensuring that the cable is not trapped.
Push the lamp into the lamp holder, and fit the lamp using the circlip.
Replace fuse and switch on .

Fitting/replacing the bulbs

When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting. Remove circlip by squeezing tabs together, to release the bulb. Twist the bulb to remove from the lamp holder.

To refit, twist the bulb into the lamp holder, fit into place. Fit the circlip into place by squeezing the tabs together and clipping into place.

Care and Cleaning

We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.

Recycling advice

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.