MICHELIN Mems Evolution 4 Liquid Proof Sensor Owner’s Manual
- June 12, 2024
- MICHELIN
Table of Contents
PRODUCT NOTICE
PRODUCT NAME MEMS
EVOLUTION-4 LIQUID PROOF SENSOR — Part Number CA1564947
PRODUCT DESCRIPTION
The MEMS EVOLUTION-4 LIQUID PROOF SENSOR is a battery powered air pressure and
air temperature sensor designed to operate inside tubeless earthmover tires.
This information is sent, via a radio transmitter, to a MEMS EVOLUTION-4
TRANSCEIVER unit, which is usually mounted in the cab of the vehicle.
FCC / IC CERTIFICATION
Model: RV1-30 FCC ID: F15-RV1-30G HVIN: RV1-30 IC: 5056A-RV130G
PMN: MEMS EVOLUTION 4 LIQUID PROOF SENSOR
Federal Communications Commission (FCC) Statement 15.19 This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference and 2) this
device must accept any interference received, including interference that may
cause undesired. 15.195(a) This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not in stalled and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own
expense.’
‘15.21 You are cautioned that changes or modifications not expressly approved
by the part responsible for compliance could void the user’s authority to
operate the equipment.”
‘FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”
- This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 29 centimeters between th e radiator and your body.
Devices shall not be used for control of or communic ations with unmanned aircraft systems.
Caution: Exposure to Radio Frequency Radiation
-
To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not
be co-located or operating in conjunction with any other antenna or transmitter.” -
To comply with RSS 192 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
PRODUCT SPECIFICATION
Physical Characteristics
- Approximate dimensions: L= 80mm. W= 70mm. H=50mm
- Approximate weight: 110g Storage Conditions
- Storage temperature: -40°C to +60°C, -40°F to + 140°F Performance Characteristics
- Normal transmission period: 60 seconds + 10 seconds
- Fast transmission period 16 seconds
- Tire compatibility: 49″ to 63″ earthmover tubeless tires
- Pressure resolution: lkPa, 0.01 bar, 0.145 psi
- Typical pressure accuracy: ± 30kPa, ± 0.3 bar, ± 4.35 psi (-20 to + 90°C, -4 to + 194°F)
- Temperature resolution: 1°C, – 1.8°F
- Typical temperature accuracy: ± 2 °C, ± 3.6°F (- 20 to + 90°C, -4 to + 194°F) RF Performance
- TX frequency: 433.92MHz ISM band
- RF output power: 86.48 dBuV/m @ 3m (Peak) as per FCC 15.231(b)
- RF data rate 5kHz
- Modulation : FSK
- Antenna: Internal helical
- With duty cycle correction as per FCC part 15.35 Electrical Performance
- Batteries: 1 x Li-metal coin cell
- Lithium content: 0.16g Operating Conditions
- Operating temperature range: -20°C to +125°C; -4°F to + 257°F
- Operating pressure range: 100kPa to 140t stAkcjarkiprig14 Now bar Absolute; 14.51 psi to 203.05 psi Absolute Environment
DISPOSAL
The MEMS EVOLUTION-4 LIQUID PROOF SENSOR must not be disposed of in landfill.
At the end of its life, the MEMS EVOLUTION-4 LIQUID PROOF SENSOR must be
removed from the tire and deposited in a container dedicated to the recycling
of electronic equipment that contains batteries. If users do not have access
to the appropriate recycling facility, your local Michelin MEMS representative
is able to provide a container dedicated to the purpose of collecting MEMS
equipment.
CONTACT DETAILS — Technical Support
For more information or assistance, please contact the Michelin MEMS
representative for your country.
Brasil, Chile & Pertl : +55 (21) 36 21 4646 USA,
Canada & Mexico : +1 864 458 5000
Australia : +61 3 86 71 1003
South Africa : +27 115 790 300
Russia : +7 495 258 09 26
China : +86 21 22855000
services.mining@michelin.com
MFP MICHELIN 23 Place des Carmes-Dechaux 63000 Clermont-Ferrand France
The product must not be disposed of with unsorted waste, but must be sent to
separate collection facilities for recovery and recycling Features,
specifications are subject to change without notification. Document version
17.0
MFP MICHELIN © 2012 All rights reserved. Exclusive property of Manufacture
Francaise des Pneumatiques Michelin. Any reproduction or utilization
prohibited without the consent of Michelin.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>