MICROWOO 2A9XL-REF Magnetic Wireless Charging Power Bank Instruction Manual

MICROWOO 2A9XL-REF Magnetic Wireless Charging Power Bank

Product Description

Product Specification

• Battery Capacity：10000mAh
• Input：5V-2A 9V-1.67A 12V-1.5A QC3.0 / PD3.0
• Wireless Charging Output：5W / 7.5W / 10W / 15W max Type-C Output：20W(iPhone）max，18W(Android）max
• Material：ABS+PC
• Logo：Can be customized
• Size：1097017mm
• Product weight：186g
• Working frequency：110-205kHz
• Transmission distance：3-8mm
• Conversion efficiency: 78%

Product instructions

1. Click the power button to turn on, and the power indicator is always on;
2. Put the mobile phone which supporting Qi wireless charging to the charging induction area and enter the charging state;
3. Remove the charging product and stand by for 70 seconds when the power indicator goes out, it will turn off automatically;
4. Double-click the power button to turn off directly;
5. The product and mobile phone can be charged through the PD charging cable;

SAFETY INSTRUCTION

1. Do not disassemble or throw into fire or water.to avoid causing a short circuit leakage .
2. Do not use wireless charger in severely hot .humidor corrosive environments.to avoid circuit damage and occurs leakage phenomenon.
3. Do not place too close with magnetic stripe or chip card (IDcard, bank cards, etc.Jto avoid magnetic failure.
4. Please keep the distance at least 20cm between implantable medical devicesotential interference with the medical device.
5. To take care of the children, to ensure that they won’t play the wireless charger as a toy.to avoid unnecessary accidents.

Notes

1. Please use qualified AC adapter. The AC adapter should be 9V / 2A or QC 3.0 or above, otherwise insufficient input electric current might cause unstable charging.
2. Do not place too close with magnetic stripe or chip card (ID card, bank cards ,etc. to avoid magnetic failure.
3. Make sure the plate doesn’t get too hot. If the plate is too warm, take your phone off the plate, and switch the plate off. The plate may switch off automatically fit is too hot. when the plate has cooled down. try charging again.
4. The led indicator will keep flashing or the charging pad will switch off by itself when charging goes wrong.

FAQ and SoluHon

1. Why the led Indicator keep flashing and my phone do not receive any charge?

   • Please make sure your mobile device is Qi-standard supported .
   • Make sure you find the right charging position.
   • Please make sure you use 9V-2A or QC 3.0 or above adapter.

2. Why H charges slowly than my original adapter came wHh the mobile device?

   • The wireless charging current size allowed by the phone itself or external receiver coil is different.
   • When the phone is charging, the standby power consumption is large, so it is recommended to reduce the phone standby program.

3. ls radlaHon from wireless charging harmful to one’s heath?
   The wireless charger emits non-ionizing radiation which is not harmful to humans.

4. My device Is hot whUe charging, Is It normal?
   If you don’t charge your device in a good charging area ,the heat dissipation may not good and it will cause your phone hot during charging. has overheat protection function.

Warranty

We provide all our customers 12 months warranty from the date of purchase.

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>