ESL VISION 5DHOC Daylight Harvesting Occupancy Microwave Sensor Installation Guide

: June 12, 2024
: ESL VISION

Table of Contents

ESL VISION 5DHOC Daylight Harvesting Occupancy Microwave Sensor
Product Usage Instructions
Installation Guide
- Wiring Guide
- Simple Remote Programming
LED INDICATORS
- DEFAULT SETTINGS
BUTTON OPERATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ESL VISION 5DHOC Daylight Harvesting Occupancy Microwave Sensor

Product Information

Product Name	5DHOC-LV SENSOR
Installation Guide	Available
Wiring Guide	Available
Dimming Driver	Required
LED	Required

Product Usage Instructions

Warning
To prevent electric shock, ensure that the fixture is powered OFF prior to installation.

Simple Remote Programming
The ESL-REM-100 (Sold Separately) is used to program the 5DHOC.
With a range of 50ft, this allows for the flexibility to re-program for any reason, at any time. Please see REM-100 spec sheet and/or instruction guide for more detailed information.

LED Indicators
The default settings for the 5DHOC-LV SENSOR are as follows:

Brightness: 100%
Sensitivity: 100%
Hold Time: 15 min
Stand-by Dim: 30%
Stand-by Time: always on

Button Operation
Either press DISP or select a MODE to program. Use the ARROWS to select each setting. Set STAND-BY TIME to (+). Press . By default, the DAYLIGHT SENSOR will highlight 10 and 300, with a DIM setting of 10%. Select the minimum threshold (10, 30, or 50) and the maximum threshold (100, 300, or 500). Change DIM level to desired percentage. Press SEND.

Installation Guide

Wiring Guide

WARNING
To prevent electric shock, ensure that the fixture is powered OFF prior to installation

Simple Remote Programming

The ESL-REM-100 (Sold Separately) is used to program the 5DHOC. With a range of 50ft this allows for the flexibility to re-program for any reason, at any time. Please see REM-100 spec sheet and/or instruction guide for more detailed information.

LED INDICATORS

BRIGHTNESS – select a level to determine the maximum lumen level at full power.
SENSITIVITY – determines how reactive the sensor will be to movement. Range and sensitivity will vary based upon the sensor installed.
HOLD TIME – the duration that the light will remain on without detecting movement before dimming or turning off.
DAYLIGHT SENSOR – uses the photocell to adjust the LED output in conjunction with the ambient light to provide consistent lighting regardless of environmental changes. Select the EYE to use a value based on the current ambient light. The numbered values correspond the footcandle conversions listed below. The SUN disables the photocell and will run the programmed settings regardless of ambient lighting.
STAND-BY – DIM will determine the maximum lumens to be used when there is no activity detected. A setting of 0% will keep the light from dimming. TIME will determine how long the light will remain at the dimming level before shutting off completely. Setting the time to will make the light remain on.

DEFAULT SETTINGS

Brightness: 100%
Sensitivity: 100%
Hold Time: 15 min
Stand-by Dim: 30%
Stand-by Time: ∞ always on

BUTTON OPERATION

ON/OFF – disables the sensor for a constant on or off position. To enable the sensor, press AUTO.
AUTO – press to start the sensor with the previously used settings. This must be used to utilize the sensor’s capabilities.
RESET – return to the default settings.
TEST – select sensitivity thresholds and press and then hold for two seconds. This will disable the standby time and daylight sensor in order to check the other settings. To exit, press AUTO.
ARROWS – use to make selections on the LED selectors. Press OK to keep the displayed selections.
OK – use to register selections or to clear selections when changing or viewing MODES
DISPLAY – show the last settings that were uploaded to the sensor or the current selections on the remote’s LED indicators.
SEND – upload and activate the current selections. The light will turn on and off to confirm. Changing the remote settings will not change the sensor settings without pressing SEND.
MODES – save preset parameters by using the MODE buttons.
TO SET:
Press MODE button on remote. LED indicators will display the current settings. Use arrows to change each parameter. Press OK to save the settings to the selected MODE. To activate the settings, aim remote at sensor and press SEND.
SMART PHOTOCELL SENSOR – off by default. When enabled, the light will be controlled by the photocell only, and the occupancy settings will be disabled. If the ambient light is less than the minimum threshold, the light will remain on, even if there is no activity. If the ambient light is more than the maximum threshold, the light will remain off, even if there is activity in the space.
TO SET:
Either press DISP or select a MODE to program. Use the ARROWS to select each setting. Set STAND-BY TIME to (+∞). Press . By default, the DAYLIGHT SENSOR will highlight 10 and 300, with a DIM setting of 10%. Select the minimum threshold (10, 30 or 50) and the maximum threshold (100, 300 or 500). Change DIM level to desired percentage. Press SEND.