PYLE SQDPB-1 Strength Training Pull-Up Bars User Guide

: June 12, 2024
: Pyle

Table of Contents

Features
What’s in the Box:
Technical Specs:
App Installation
Installation Notes
Gravity Enhancement Tips
Product Overview
Questions? Comments?
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**PYLE SQDPB-1 Strength Training Pull-Up Bars

**

Features

Easy to Install
Diamond-Like Base Disperses Pressure
Steel Pipe Reinforcement
Removable and Easy to Carry
Increase Thicker Non-Slip Rubber Pad
32″ Anti-Skid Horizontal Bars
Holds up to 440 Pounds
Soft Anti-Skid PVC Material
Enlarge Anti-Skid Block
Large Contact Area and High Resistance
No Screws and Drilling Required
Adjustable Pull up Bar
Suitable for Standard Doorway
Protects Door Frames from Cracking
High-Quality Load-Bearing Steel
Safety with Deadlock Design Pull-Up Bars
Non-Slip, Non-Toxic, Non-Smell and Comfortable
Chin up Bar can be Adjusted in Width to Fit in Door Frame
Level-Meter can Help Install Chin-Up Bar in the Balance State
Non-Slip Soft Foam Handle Minimize Hand Fatigue and Pain

What’s in the Box:

Doorway Pull Up and Chin Up Bar

Technical Specs:

Construction Material: (Metal Part) Iron Pipe,
(Rubber Part) PVC, (Plastic Part) ABS，(Foam) EVA
Weight Capacity: 4.41lbs
Length: 29.5” – 45” inches
Product Dimensions (L x W x H): 29.5-45.3” x 4.1” x 6.9” in.

App Installation

Installation Notes

Step 1: Loosen the locks on both sides outwards and extend the horizontal bar to the same width as the mounting surface.
Method One:
Place the horizontal bar horizontally on a clean ground, keep both ends still, hold the foam in the middle, and rotate it in the direction of the arrow to extend the horizontal bar.
Method Two:
Sit on a chair or sofa, place the horizontal bar horizontally on our legs, and the main body in the middle does not move, rotate the two ends of the horizontal bar in the opposite direction of the arrow to extend the horizontal bar.
Method Three:
Sit on a chair or sofa, place the horizontal bar upright, the main body in the middle does not move, and rotate the two ends of the horizontal bar in the opposite direction of the arrow to extend the horizontal bar.

Step 2: Tighten the horizontal bar firmly and fix it on the mounting surface.
Fixing Method: Hold one end of the horizontal bar with one hand and place the other end of the horizontal bar againstthe mounting surface, and then hold the middle foam with one hand and rotate it in the direction of the arrow until both ends are against the mounting surface (make sure the horizontal bar is level and the bubbles in the level are stable in the center), and then continue to tighten in the direction of the arrow until the horizontal bar is tightened.

Note: The direction of the big foot board (upper narrow and lower width)

Reinforcement tips

Be sure to rotate in the direction indicated by the vertical arrow in the red part until the horizontal arrow in the red part is aligned with the main pole card slot;
Align the entire lock buckle with the main bar slot and push it in to reinforce the horizontal bar;
After fixing, rotate the main rod in the opposite direction of the arrow.
If it cannot be rotated, it is really fixed;
When disassembling, push the buckle out of the slot before disassembling.

Step 3: After the horizontal bar is fixed, close the locks at both ends to improve safety
Reinforcement Method: Stretch the red part inside the lock, rotate it in the direction of the vertical arrow, align the horizontal arrow with the groove of the main pole, and then insert it forcefully (if you encounter resistance, stretch the red part again.)
(Reminder: There will be a certain sound when the lock is inserted, which is normal)

Reminder: After we receive the horizontal bar, if the lock and the pole are tight and the big foot pole is difficult to turn out, we must first loosen the locks on both sides.

Solution: We can first take out the horizontal bar from the package, hold the red part of the lock buckle in one hand, hold the black part of the lock buckle in the other hand and pull it out; let it rotate in the opposite direction of the vertical arrow, then release the lock buckle and turn it out Bigfoot.

Gravity Enhancement Tips

When the horizontal bar receives more gravity, the buttons on both ends will slide down, which is a normal phenomenon;
When the button slides down, the two sides of the horizontal bar will protrude outward, forming a triangular structure. Increasing the supporting force of the wall guarantees your safety.