V I V O STAND-V100C Single Ultrawide Monitor Desk Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
V I V O STAND-V100C Single Ultrawide Monitor Desk Mount
Product Information
This product is a Single Ultrawide Monitor Desk Mount designed to securely hold a monitor on a desk. It comes with various components and hardware for assembly.
Package Contents
| Component | Quantity |
|---|---|
| VESA Plate | 1 |
| VESA Bracket | 1 |
| Clamp | 1 |
| Pole | 1 |
| Pole Cap | 1 |
| Support Plate | 1 |
| Cable Clip | 1 |
| Grommet Plate | 1 |
| Pad | 5 |
| S-A (M6x16mm Screw) | 3 |
| S-B (M6x10mm Thumbscrew) | 1 |
| M-A (M4x12mm Screw) | 4 |
| M-B (M4x16mm Screw) | 4 |
| M-C (M5x12mm Screw) | 4 |
| M-D (M5x16mm Screw) | 4 |
| M-E (M5 Washer) | 4 |
| M-F (Spacer) | 4 |
| T-A (4mm Allen Wrench) | 1 |
| T-B (6mm Allen Wrench) | 1 |
Weight Capacity: Up to 44 lbs (20 kg)
Product Usage Instructions
Step 1
- Press the Pole Cap (E) into the Pole (D), using the side without internal threading.
Step 2 (Option A): Clamp Installation
- Install the Pole (D) to the Clamp (C) using the M6x16mm Screws (S-A) and the 4mm Allen Wrench (T-A). Remove the protective film from Pads (H) and apply them to the Clamp (C) as shown. Secure the clamp assembly to the desktop by tightening the hand bolt.
Step 2 (Option B): Grommet Installation
- Remove Screw (C1) from Clamp Bolt (C2) and remove Clamp Bolt (C2) from Clamp (C). Remove the protective film from Pads (H) and apply them to the bottom side of the Grommet Plate (G). Align the pin on top of the Grommet Plate (G) with the small hole on the bottom of Pole (D) and position the parts over the grommet hole. Attach to the desktop using Support Plate (I) and Clamp Bolt (C2). If there is no existing grommet hole available, drill a 13/32 (10mm) hole or larger in your desired mounting location.
Step 3:
- Slide the Pole Cable Clip (F) and VESA Bracket (B) onto the Pole (D). Adjust the height location of the VESA Bracket (B) and tighten it using the 6mm Allen Wrench (T-B).
Step 4:
- Mount the VESA Plate (A) to the monitor using the appropriate Screws (M-A to M-D), M5 Washers (M-E), and Spacers (M-F).
Step 5:
- Slide the monitor with the VESA Plate onto the VESA Bracket (B) and secure it using the M6x10mm Thumbscrew (S-B).
Step 6:
- Use the Cable Clip (F) to route cables. Store the Allen Wrenches (T-A, T-B) in the slots of the Clip.
- Important: Keep the displays positioned over the desktop within the arrow range shown. Adjust the tension of the Monitor Bracket (B) using the 6mm Allen Wrench (T-B) as desired.
- If you have any questions or need assistance, please contact our dedicated support team at [email protected] or call 309-278-5303. Our support team is available Monday-Friday from 7:00 am-7:00pm CST.
- For more information, visit our website at https://vivo-us.com/products/stand-v100C
- Love your new VIVO setup and want to share? Tag us in your photo on social media! @vivo_us
- Last Updated: 04/06/2023 REV1
WARNING!
- If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
- Improper installation may cause damage or serious injury.
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
- SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
NOTE: SOME HARDWARE MAY NOT BE USED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
- Press Pole Cap (E) into Pole (D), using the side without internal threading .
STEP 2 (Option A)
- Clamp Installation
- Install Pole (D) to Clamp (C) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Remove protective film from Pads (H) and apply them to Clamp (C) as shown.
- Secure clamp assembly to desktop by tightening hand bolt.
STEP 2 (Option B)
- Grommet Installation
- Remove Screw (C1) from Clamp Bolt (C2) and remove Clamp Bolt (C2) from Clamp (C).
- Remove protective film from Pads (H) and apply them to the bottom side of Grommet Plate (G).
- Align the pin on top of Grommet Plate (G) with the small hole on the bottom of Pole (D) and position the parts over the grommet hole. Attach to the desktop using Support
- Plate (I) and Clamp Bolt (C2). If there is no existing grommet hole available, drill a 13/32” (10mm) hole or larger in your desired mounting location.
STEP 3
- Slide Pole Cable Clip (F) and VESA Bracket (B) onto Pole (D). Adjust the height location of VESA Bracket (B) and tighten using the 6mm Allen Wrench (T-B).
STEP 4
- Mount VESA Plate (A) to monitor using appropriate Screws (M-A thru M-D), M5 Washers (M-E), and Spacers (M-F).
STEP 5
- Slide monitor with VESA Plate onto VESA Bracket (B) and secure using M6x10mm Thumbscrew (S-B).
STEP 6
- Use Cable Clip (F) to route cables. Store Allen Wrenches (T-A, T-B) in slots of Clip.
WARNING
- Keep the displays positioned over the desktop within the arrow range shown.
ADJUST AS DESIRED
-
Use 6mm Allen Wrench (T-B) to loosen or tighten Monitor Bracket (B) tension.
-
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
-
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times.
-
If any parts are received damaged or defective, please contact us.
-
We are happy to replace parts to ensure you have a fully functioning product.
-
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
-
www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
-
Chat live with an agent!
-
[email protected] AVG. RESPONSE TIME (within office hrs): 1HR 8M
-
23% within < 15m
-
38% within < 30m
-
61% within < 1hr
-
83% within < 2hr
-
92% within < 3hr
-
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
-
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
Documents / Resources
| V I
V O STAND-V100C Single Ultrawide Monitor Desk
Mount
[pdf] Instruction Manual
STAND-V100C Single Ultrawide Monitor Desk Mount, STAND-V100C, Single Ultrawide
Monitor Desk Mount, Ultrawide Monitor Desk Mount, Monitor Desk Mount, Desk
Mount, Mount
---|---
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Single Ultrawide Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more