Princeton Tec Switch Rgb Helmet Light Instructions
- June 12, 2024
- Princeton Tec
Table of Contents
Princeton Tec Switch Rgb Helmet Light
Product Information
The Helmet Light is a versatile lighting device designed for use with helmets. It comes in two versions: Switch RGB (White mode version) and Switch RGBIR (IR mode version). The product operates using batteries and has different modes and colors to suit various needs.
Switch Operation:
Switch RGB (White mode version):
- Starts in color mode
- Press 1x: Color Low
- Press 2x: Color High
- Press 3x: Off
- Press & Hold: Next Press cycles through the available colors
- Press & Hold for 5 seconds from off: Programming mode
Switch RGBIR (IR mode version):
- Starts in IR mode
- Press 1x: IR Low
- Press 2x: IR High
- Press 3x: Off
- Press & Hold: Next Press cycles through the available colors
- Press & Hold for 5 seconds from off: Programming mode
Programming Mode:
In programming mode, you can customize the color settings. Follow these steps:
- The Switch RGB ships with red light selected.
- From off, press and hold for 5 seconds to enter programming mode.
- When in programming mode, click to activate the desired color (Red, Blue, or Green).
- Press and hold for 5 seconds to exit programming mode and save changes.
Troubleshooting:
If the Switch RGB fails to light:
- Check the batteries and replace if necessary.
- If the issue persists, contact Princeton Tec customer service for repair or replacement.
Product Usage Instructions
Helmet Light Installation:
- Back the screw out so the end of the screw is flush with the metal U-clip.
- Slide the exposed U-clip over the bottom edge of your helmet with the metal clip on the inside and the plastic base exposed on the outside of your Helmet.
- Holding Mount firmly upward, tighten the center slotted screw until it stops.
ARC Rail Adapter Installation:
Note : Do not overtighten the center anti-slip lock screw.
- Slide the ARC Rail Adapter into the ARC rail to the desired position.
- Secure the ARC Rail Adapter in place with the center anti-slip lock screw.
Please refer to the product manual for more detailed instructions and safety information.
Battery Installation
See Figure 1
(2) CR2016 Coin Cells – 6V
Princeton Tec cares about the environment and recommends recycling batteries. For more information about battery recycling, please go to: batteryrecycling.com To install the batteries, rotate light unit out of base. Lift tab of battery door on the underside of the light unit to expose the coin cell(s)
Install coin cell(s) batteries with the (+) positive side facing up. Improper installation of the batteries will damage the light and void the warranty.
Replace the battery door with the lift tab properly aligned with the lift tab slot of the housing. Press the door firmly in place making sure it is all the way seated in place.
WARNING! Never mix fresh and used batteries. Never mix different battery brands or chemistry types. Always remove drained batteries immediately. Remove batteries during long periods of storage.
Switch Operation
Switch RGB (White mode version)
See Figure 2a
Starts in color mode
- Press 1x Color Low
- Press 2x Color High
- Press 3xOff
- Press & Hold in color modeWhite High
- Next Press Off
- Press & Hold 5s in off Programming mode
Switch RGBIR (IR mode version)
S ee Figure 2b
Starts in IR mode
- Press 1x IR Low
- Press 2x IR High
- Press 3x Off
- Press & Hold in IR mode color High
- Next PressOff
- Press & Hold 5s in off Programming mode
Programming Mode
See Figure 3
- The Switch RGB ships with red light selected
- From off, press and hold for 5 seconds to enter programming mode
- When in programming mode, click to activate the desired color (Red, Blue, or Green)
- Press and hold for 5 seconds to exit programming mode and save changes
Figure 4 ARC Rail Installation
- Slide ARC Rail Adapter into ARC rail to desired position and secure in place with center anti-slip lock screw.
- DO NOT OVERTIGHTEN this screw.
Figure 5 MOLLE Mount
- Slide clip inside any strap position, pinch MOLLE strap to hook the lower end of the metal clip onto the strap.
Figure 6 M-LOK® Mount
- Insert screw and T-nut into M-LOK® mount. T-Nut “gap” must be slightly greater than the thickness of the mounting surface.
- Slide mount on to M-LOK® rail and tighten with a screwdriver.
Figure 7 MICH Mount Installation
- Back the screw out so the end of screw is flush with metal U-cli p. Slide the exposed U-clip over the bottom edge of your helmet with the metal clip on the inside and the plasti c base exposed on the outside of your Helmet.
- Holding Mount firmly upward, tighten center slotted screw until it stops.
Figure 8 Picatinny Rail Mount
- Remove the center through screw from the side of the Picatinny base mount. Slide Picatinny to desired position and insert side locking screw aligning with any slot in Picatinny rail and tighten to clamp in place.
- DO NOT OVERTIGHTEN this screw.
Figure 9 (ABR) Above Rail Mount
- A. If using MPLS ABR on a ballistic helmet, skip to step two. For use with nonballistic helmets, begin by snapping off unneeded portion of ABR mount by hand or with a pair of pliers, and discarding the smaller ‘hook’ portion
- B. Loosen or remove front rail screw, and slide ABR into desired position beneath rail. Retighten front rail screw.
- C. Select Charge MPLS mount and secure with included machine screws, gently tightening with a Phillips screwdriver. Install Switch/Point onto the mount.
Troubleshooting
If the Switch RGB fails to light:
- Check the batteries for proper
- Replace batteries if proper installation is
- This light has been designed to Check the light for water contamination on the circuit board. The light will resume normal operation once any water is shaken or blown out and the light is left open until completely dry. If the light has been contaminated with salt water, flush the unit with fresh water and dry as described above.
USA– International 1-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free from defects in workmanship and materials under normal use for one year. This warranty covers all of the component parts of the product except batteries. This warranty does not cover deterioration due to normal wear or damage due to misuse, alteration, negligence, accidents, or unauthorized repair. Princeton Tec will repair or replace parts that are defective in workmanship or materials. Your authorized Princeton Tec Dealer and Princeton Tec are the only facilities authorized to repair the product. After (3) unsuccessful attempts (within the warranty period) to repair the product, you have the right to elect re- placement of the product or a refund of the purchase price less allowance for use of the product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Princeton Tec reserves the right to change product specifications without notice.
FOR CALIFORNIA RESIDENTS
WARNING : This product contains Bisphenol A (BPA) a chemical known to the State of California to cause birth defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
- Check Replace if necessary.
- To send your light in for repair or replacement, first contact Princeton Tec customer service on 1-800-257-9080 to request an RMA number. Please have your light model, date of purchase and a brief description of the fault your are experiencing. No warranty repairs will be accepted without an RMA number.
- Return the light to: Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and freight collect items will not be
- Upon receipt your light will be processed in about two Please allow additional time for return transportation from NJ.
Princeton Tec
PO Box 8057, Trenton, NJ 08650 Phone :
609-298-9331 Fax :
609-298-9601
princetontec.com © 2023 Princeton Tec.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>