Defiant DFI-5852-BK Motion Security Light User Manual

Defiant DFI-5852-BK Motion Security Light User Manual

THANK YOU
We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Defiant!

Safety Information

PRECAUTIONS

• Please read and understand this entire manual before attempting to assemble, install, or operate this light fixture.
• This light fixture requires a 120-Volt AC power source.
• Some codes require installation by a qualified electrician.
• This light fixture must be properly grounded.
• This light fixture should be installed outdoors on a wall or eave.
• The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area.

WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture.

WARNING: Risk of fire. Keep the lamp heads at least 2 in. (51 mm) from combustible materials.

CAUTION: Burn hazard. Allow the light fixture to cool before touching it.

NOTICE: Do not connect this light fixture to a dimmer switch or timer.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  CAN ICES-005 (B)/NMB-005 (B)

Warranty

5-YEAR LIMITED WARRANTY
WHAT IS COVERED
This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from the date of purchase. A purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED
This guarantee does not include repair service, adjustment, and calibration due to misuse, abuse, negligence, or LEDs. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product. No service parts are available for this product. Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.

Pre-Installation

PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture. Estimated installation time: 30 minutes

SPECIFICATIONS

TOOLS REQUIRED

Pre-Installation (continued)

HARDWARE INCLUDED

PACKAGE CONTENTS

Installation

Determining the mounting location

NOTE : The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area.

• Determine the mounting location – wall or eave mount.
• Position the lamp heads (A) in the general direction of the desired light coverage.

Removing the mounting plate
NOTE: This fixture comes with a mounting plate (D). It is pre-assembled on the light fixture (B) for shipping.
NOTE: The large mounting bolt (EE) is pre-installed in the light fixture (B). Do not attempt to remove the large mounting bolt (EE).

• Unscrew the large mounting bolt (EE) connecting the light fixture (B) to the mounting plate (D) and remove the mounting plate (D).

Installing the mounting bracket
WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture.

NOTE: Four mounting bracket screws of various sizes are included. The installation will only require two. Discard the unused mounting bracket screws after installation.

• Remove the existing light fixture.
• Install the mounting bracket (FF) with the stamped word “FRONT” facing away from the junction box.
• Use the mounting bracket screws (BB or CC) that best fit the junction box. If necessary, use the screws that were removed from the existing light fixture.
• Firmly pull on the mounting bracket (FF) to verify it is securely mounted to the junction box.

Installation (continued)

Installing the mounting plate

• Route the junction box wires through one of the large holes in the gasket (HH).
• Route the junction box wires through the hole in the mounting plate (D).
• Place the gasket (HH) and the mounting plate (D) against the junction box and align the center holes with the hole in the mounting bracket (FF).
• When mounting to a wall, the “UP” arrow must point upward.
• When mounting to an eave, the “UP” arrow must point toward the building.
• Insert the small mounting bolt (DD) through the mounting plate (D) hole located below the threaded hole and through the gasket (HH) hole, and thread it into the center hole of the mounting bracket (FF).
• Tighten the bolt (DD) securely.
• Firmly pull on the mounting plate (D) to verify it is securely attached to the mounting bracket (FF).

NOTICE: Ensure the gasket (HH) is wrinkle-free and centered between the mounting plate (D) and the mounting surface.
NOTICE : When attaching this light to an external, surface mount junction box, ensure the gasket (HH) is centered on the junction box and the mounting plate (D) presses against the gasket (HH) evenly.

Making the electrical connections

• If necessary, strip 3/8″ of insulation from junction box wires (1).
• Insert the junction box wires into the side of the terminal block and around the ground screw. Tighten terminal block screws using the mini-screwdriver (GG) and ground screw to secure the wires.
• Insert the white wire from the junction box into the terminal marked “N (White)”.
• Insert the black wire from the junction box into the terminal marked “L (Black)”.
• Connect the bare or green ground wire from the junction box to the ground screw (marked with “GND”).

Mounting the light fixture
NOTICE: The two pins on the rear of the light fixture must be inserted into the terminal block for the light to work.

• Align the top edge of the light fixture (B) with the top edge of the mounting plate (D). Tilt the light fixture (B) toward the mounting plate (D), making sure the light fixture (B) is centered on the mounting plate (D).
• Tighten the large mounting bolt (EE) securely through the center of the mounting plate (D). Do not over-tighten.
• Push the rubber plug (AA) firmly into the mounting bolt hole on the light fixture (B).

NOTICE: When attaching this light to an external, surface mount junction box, caulk around the inside of the light fixture (B) before attaching it to the mounting plate (D).

Caulking around the light fixture
IMPORTANT: Failure to completely caulk around the gasket (HH) and the mounting plate (D) could lead to water damage and is not covered under warranty.

• Caulk around the gasket (HH) and mounting surface with silicone sealant (not included).
• Caulk around the mounting plate (D) and gasket (HH) with silicone sealant (not included).

Operation

Adjusting the lamp heads
WARNING: Risk of fire. Keep the lamp heads at least 2 in. (51 mm) from combustible materials.
CAUTION: Keep lamp heads 30° below horizontal to avoid water damage and electrical shock.

• Turn the power on at the circuit breaker or fuse and turn on the wall switch.
•  If needed, gently grasp the lamp heads (A) and tilt them up or down or side to side to adjust the light coverage area.

Setting the sensor for testing
NOTE: When the “Test / Timer” control is set to the “Test” position, the light fixture will operate during the day or night. The light will stay on for 8 seconds after all motion is stopped.

• Turn the “Test / Timer” control fully counterclockwise to the “Test” position.
•  Turn the “SENS” control fully clockwise to the minimum position.
• NOTE : The motion sensor will need to completely warm up (60 seconds) before beginning the setup process.

Test 10Min SENS

• Adjusting the motion sensor detection zone
•  Perform a “walk test”: walk in an arc across the front of the motion sensor (C).
•  Watch the light. The light will come on and the red LED will flash indicating motion has been detected.
•  Stop, wait for the light to turn off, and then begin walking again.
•  Continue this process until the detection zone has been established.
• If needed, gently grasp the motion sensor (C) and move it from side to side or up and down to adjust the detection zone.

Adjusting the SENS control

• To increase the sensitivity, turn the “SENS” control counterclockwise.
• To decrease the sensitivity, turn the “SENS” control clockwise.
  NOTE : The motion sensor (C) is more sensitive to motion moving across the front of the sensor. The motion sensor (C) is less sensitive to motion moving directly toward the front of the sensor.
  NOTE: The higher the “SENS” setting (sensitivity), the greater the possibility of false triggering. To reduce false triggering, turn the “SENS” control clockwise.

Test 10 Min SENS

Adjusting the TEST / TIMER control
NOTE: The “Test / Timer” control determines the amount of time the light will stay on fully bright after all motion has stopped.

• After all, adjustments are complete, turn the “Test / Timer” control clockwise and select a time between 10 seconds (10S) and 10 minutes (10Mins).
• The light will only work at night after a time has been selected.

Switching motion detection
OFF and ON
NOTE: This light fixture can operate as a motion detection light (default from the factory) or as a dusk-to-dawn (nighttime) light. The wall switch controlling the light is used to select the desired mode. In either mode, the light will only operate at night.

IMPORTANT: THIS LIGHT FIXTURE MUST BE WIRED THROUGH A WALL SWITCH IN ORDER TO USE THE MOTION-OFF FEATURE. IF THE LIGHT FIXTURE IS WIRED DIRECTLY TO THE HOUSE WIRING WITH NO WALL SWITCH, THEN THE MOTION OFF FEATURE CANNOT BE SET.

To switch between modes

• Ensure the power to the light is ON and the sensor has warmed up (60 seconds).
• Switch the power OFF–ON–OFF–ON at the wall switch within 3 seconds.
• The light will stay in the selected mode until the above steps are performed again.
• To increase the time, turn the “Test / Timer” control clockwise.
• To decrease the time, turn the “Test / Timer” control counterclockwise.

IMPORTANT: IF THERE IS A POWER OUTAGE OR THE THE WALL SWITCH TO THE LIGHT FIXTURE IS TURNED OFF FOR MORE THAN 5 SECONDS, THE LIGHT WILL DEFAULT TO THE LAST SELECTED MODE SETTING I  WAS SET TO BEFORE THE POWER OUTAGE.

NOTE:

• If motion detection mode is set to ON, the red LED behind the motion sensor lens will blink indicating motion has been detected.
• If the motion detection mode is set to OFF, the red LED behind the motion sensor lens will not blink.

Care and Cleaning

To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only.

• Do not use paints, solvents, or other chemicals on this light fixture. They could cause premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty.
• Do not spray the light fixture with a hose or power washer.

Troubleshooting

□       The fuse is blown or the circuit breaker is turned off.

□       The light fixture is not properly attached to the mounting plate, if this is a new installation (the pins are not fully seated in the terminal block).

□       Daylight turn-off (photocell) is in effect.

□       The circuit wiring is incorrect (if this is a new installation).

□       The motion sensor is aimed in the wrong direction.

□       The outside air temperature is close to the same as a person’s body heat.

| □       Turn the light switch on.

□       Replace the fuse or turn the circuit breaker on.

□       Re-install the light fixture to the base and ensure the pins are fully seated in the terminal block.

□       Recheck after dark.

□       Verify the wiring is correct.

□       Re-aim the motion sensor to cover the desired area.

□       Increase the “SENS” setting.

The light comes on during the day.| □       The motion sensor may be installed in a relatively dark location.

□       The “Test / Timer” control is in the “Test” position.

| □       The light fixture is operating normally under these circumstances.

□       Set the “Test / Timer” control to a timed setting.

The light comes on for no apparent reason.| □       The motion sensor may be sensing small animals, automobile traffic, or other heat sources.

□       The “SENS” control is set too high.

□       The outside temperature is much warmer or cooler than a person’s body heat (summer or winter).

□       The light fixture is wired through a dimmer or timer.

| □       Decrease the “SENS” setting or reposition the motion sensor.

□       Decrease the “SENS” setting.

□       Decrease the “SENS” setting.

□       Do not use a dimmer or timer to control the light fixture. Replace the dimmer or timer with a standard on/ off wall switch.

Troubleshooting (continued)

heat source, such as an air vent, dryer vent, or brightly painted, heat- reflective surface.| □    Decrease the “SENS” setting or reposition the motion sensor.
| □    The motion sensor is in motion off mode (the red LED behind the motion sensor lens is not blinking).| □    Switch the motion sensor to motion on. See Switching motion detection OFF and ON on page 9.
| □    The light fixture is wired through a dimmer or timer.| □    Do not use a dimmer or timer to control the light fixture. Replace the dimmer or timer with a standard on/ off wall switch.
| □ The light fixture is on the same circuit as a motor, transformer, or fluorescent bulb.| □    Install the light fixture on a circuit without motors,

transformers, or fluorescent bulbs.

The lights flash on and off.| □    Heat or light from the bulbs may be turning the motion sensor on and off.| □    Reposition the lamp heads away from the motion sensor.
| □    Heat is being reflected from other objects and may be turning the motion sensor on and off.| □    Decrease the “SENS” setting or reposition the motion sensor.
| □    The motion sensor is in “TEST” mode and warming up.| □    While in “TEST” mode, the light only stays on for 8 seconds. Set the “Test / Timer” control to a timed setting.

Questions, problems, missing parts?
Before returning to the store, call Defiant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday 1-866-308-3976
HOMEDEPOT.COMRetain this manual for future use.

Download PDF:Defiant DFI-5852-BK Motion Security Light User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>