VEVOR PD220 Heat Press User Manual

VEVOR PD220 Heat Press User Manual

Operation Introduction

Note: Press (+/-) to switch Fahrenheit and Celsius

Safety instruction

Before operating this unit, please read these instructions completely and save them

Notice

This machine adopts eccentric bearing structure, it is strictly forbidden to adjust the pressure too much to avoid damage to the bearing

Keep unplug when moving the machine

Keep unplug when installing accessories

Place on a flat and stable platform and operate under ventilated conditions

Wear special protective equipment when operating the machine

Warning Improper use may result in electric shock, fire, personal injury and other damage.

Ꮻ Do not use this machine in a hazardous location

Ꮻ Do not use when the machine is not working properly.

Ꮻ Do not allow children or adults who do not understand this manual to operate this machine.

Ꮻ Do not disassemble and repair this machine.

Ꮻ Do not use an unsuitable AC outlet.

1. Manual countdown

2. .Long press for 3 seconds to set automatic shutdown time (factory default 240minutes)

3. Countdown reset

4. Set the temperature set the time

5. Long press for 3 seconds to correct temperature +30 degrees or -30degrees

Three settings can be stored

Temperature conversion

Fahrenheit-Celsius

Operation Steps

1. Set the temperature, such as ceramic mug 180 degrees, 180 seconds
2. After the temperature reaches 180 degrees, put the mug with the sublimation paper in the machine, press down the handle, and use moderate force.
3. The machine will count down automatically after the handle is pressed down, and the mug can be taken out after the countdown is completed

Accessories installation diagram

Main spare parts

1. Handle: put pressure on
2. Adjusting lever
3. Guide rod
4. Display screen
5. Button
6. Power socket
7. Overload protector
8. Power switch
9. Aviation connector
10. Heating pad

Adjusting rod: adjust the pressure of the heater according to the mug specifications.
Guide rod: to ensure that the pressure at both ends of the mug heater is balanced.

Common problem

E1/E2: E1/E2 appearing on the display means that there is a short circuit/open circuit in the temperature probe wire (that is, the wire is broken and connected to cause a short circuit, and the open circuit means that the wire is broken or the plug wire falls off). Check the aviation connector of the mug heater.

1. Before working, you need to prepare the correct materials: sublimation mugs, sublimation paper, etc.
2. The pattern turns yellow/brown: reduce the temperature or reduce the time.
3. The color of the pattern is light/white: it is necessary to increase the temperature or add time.
4. Mug heater bubbles: need to be replaced with new ones.
5. Temperature not rise: Check whether the heater wiring and the controller are plugged in tightly.

Electrical schematic diagram

Circuit Board Wiring Method

1. (HEAT)Heating plate input live wire
2. (N)The main incoming line zero line n
3. (COM)Heating plate input zero line
4. (L)Main incoming line L
5. (CON1)Button switch line
6. (CON3)Motherboard and display cable EAT
7. (CON2)NTC temperature probe wire

Transfer Parameter(for reference)

Aluminum bottle|
Vacu um cup|
11 oz mug|
12oz mug
---|---|---|---
180°C(360° F)| 180°C(360° F)| 180°C(360° F)| 180° C(360° F)
90S| 90S| 180S| 180S

  Main parameters

Guarantee

The products are strictly based on the Consumer Protection Law of the People’s Republic of China and the Product Quality Law of the People’s Republic of China. The services are as follows:

Within 12 months, this product has the performance failure listed in the “Product Performance Failure Table”. It is confirmed by manufacturer and can be used for maintenance service free of charge. If out of validity, damage caused by force majeure, or human causes, the machine is not covered by the warranty, repair in charge.

warranty content

Product Performance Failure Table

Mach ine body| Parts of the machine itself (excluding main parts)| One year| Fault 1| The machine cannot be used normally according to the operating procedure
---|---|---|---|---
Main parts| PCB A(circu it board)| One year| Fa ult 3        Display error
Mu g heating element| 90days        Fault 4         Failure heating

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>