BEGA 24042 Ceiling and Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Dimension
Application
Product description
Safety
Overvoltage protection
Lamp
24 042K3
24 042K4
Installation
Replacing the LED module
Cleaning · Maintenance
Spares
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24042 Ceiling and Wall Luminaire

BEGA 24042 Ceiling and Wall Luminaire

Dimension

Application

Ceiling and wall luminaire with hand-blown, satin matt opal glass. For a soft and uniform light distribution.
Some of the light exits behind the shield and also illuminates the mounting surface.

Product description

Luminaire made of aluminium alloy
and stainless steel
BEGA Unidure® coating technology
Opal glass satin matt
Silicone gasket
2 mounting holes ø 5.5mm
Distance apart 190mm
2 cable entries for through-wiring of mains
supply cable ø 7-10.5mm
Connecting terminal 2.5@
with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 x 0/50-60 Hz
DC 176-264 V
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK05
Protection against mechanical
impacts < 0.7 joule
– Safety mark
– Conformity mark
Weight: 1.8 kg

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at
www.bega.com.

Lamp

Module connected wattage 7.8 W
Luminaire connected wattage 9 W
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C\

24 042K3

Module designation LED-0916/830
Colour temperature 3000 K Colour rendering index CRI >80
Module luminous flux 1450 lm
Luminaire luminous flux 1008 lm
Luminaire luminous efficiency 112 lm/W

24 042K4

Module designation LED-0916/840
Colour temperature 4000 K
Colour rendering index CRI >80
Module luminous flux 1470 lm
Luminaire luminous flux 1022 lm
Luminaire luminous efficiency 113,6 lm/W

Installation

Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.

Push plug into coupler as far as it will go.
Make sure that gasket is positioned correctly.
Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.

Disconnect the system.
Turn the opal glass with the integrated LED unit to the left as far as it will go, and remove it. Disconnect the plug-in device.
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relapsing.

To dismantle the LED unit, the two springs must be removed.
To do this, use a small screwdriver to move the spring clip resting against the hexagon socket screw upwards and over the head of the screw (see drawing A).
The spring can then be removed.
Loosen the hexagon socket screws and take the LED unit out of the opal glass.
Replace the LED modules.
Please follow the installation instructions for the LED module.
Insert the LED unit into the opal glass and secure it in place.
Then insert the springs at the two opposite hexagon socket screws.
Make sure that the spring clip is properly located behind the heads of the screws (see drawing B).

Replacing the LED module

Push plug into coupler as far as it will go.
Make sure that gasket is positioned correctly.
Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.