SUSSEX BEBM85 Calibre Basin Mixer Installation Guide
- June 12, 2024
- SUSSEX
Table of Contents
SUSSEX BEBM85 Calibre Basin Mixer
Product Information
The Suba Basin Mixer is a high-quality tapware product designed and manufactured by Sussex Taps Pty Ltd. It features a stylish design and is available in different models:
- CBM – Basin mixer
- BBM – Basin mixer with extended 85mm outlet
- BEBM85 – Extended basin mixer with 85mm outlet
- BEBM125 – Extended basin mixer with 125mm outlet
- BLBM – Lever basin mixer
- BLEBM85 – Lever basin mixer with extended 85mm outlet
- BLEBM125 – Lever basin mixer with extended 125mm outlet
The Suba Basin Mixer is water-efficient, with a water rating of 3.0 litres per minute, complying with AS/NZS 3718:2005 and licensed under License No. 20081. It is suitable for installation by a licensed plumber, following the guidelines provided in AS/NZS 3500:2003.
Product Usage Instructions
- The Suba Basin Mixer comes pre-assembled. Remove only the Fixing nut and Clamp before installation.
- Lower the Mixer onto the mounting surface and attach the Flexible Hoses.
- In some cases, feed the Flexible Hoses through from under the mounting surface and tighten using an appropriate spanner.
- Secure the Flexible Hoses, then attach the Clamp and Fixing Nut from underneath.
- Ensure that the Base O Ring is intact and the Mixer is centered over the mounting surface hole before fully securing it.
- The mounting surface must be completely sealed and water-tight.
- Ensure that the matching threads of the 1/2 BSP Fittings on the Flexible Hoses are cut square and burr-free.
- Flush all pipework thoroughly and make sure it is free from any dirt or debris before connecting the Flexible Hoses.
- It is recommended to use Isolating Stop Valves (not supplied) with all installations.
- Connect the Flexible Hoses to Hot and Cold pipework fittings, ensuring they do not kink or become twisted during tightening.
- Check all fittings and connections to ensure they are secure and water-tight.
Plumber Note
When conducting on-site testing with higher water pressures, make sure the Mixer is in the closed position (STATIC TEST). Do not open the Mixer when exceeding the maximum stated water pressure. After testing, do not relieve high water pressure by operating the Mixer. Exposing the internals of the Mixer Cartridge to higher than specified water pressures will void the manufacturer’s warranty.
Maximum working water pressure for the Suba Basin Mixer is 300-500 kPa, and the maximum water temperature is 65°C.
For more information, visit
www.sussextaps.com.au or refer to AS/NZS 6400
License No. 0124.
For water efficiency ratings, visit
www.waterrating.gov.au.
Product code
- BBM Basin mixer
- BEBM85 Extended basin mixer 85mm outlet
- BEBM125 Extended basin mixer 125mm outlet
- BLBM Lever basin mixer
- BLEBM85 Lever extended basin mixer 85mm outlet
- BLEBM125 Lever extended basin mixer 125mm outlet
Installation guidelines
- The Mixer is supplied assembled, only the Fixing nut and the Clamp need to be removed.
- After removing the mentioned parts, lower the Mixer on to the mounting surface and fit the Flexible Hoses.
- In some cases the Flexible Hoses may need to be fed through from under the mounting surface and then attached. (Tighten using appropriate spanner)
- After securing the Flexible Hoses, fit Clamp and attach the Fixing Nut from underneath.
- Before fully securing the Mixer ensure that the Base O Ring is intact and the Mixer is properly centered over the mounting surface hole.
- The Mixer mounting surface must be completely sealed and water-tight.
- The 1/2” Fittings of the Flexible Hoses have a conical seal, ensure that the matching threads are cut square and burr free.
- Prior to connecting the Flexible Hoses, ensure all pipework is thoroughly flushed and ensure pipework is free of any dirt or debri.
- Isolating Stop Valves are recommended with all installations. (not supplied)
- Connect the Flexible Hoses to Hot and Cold pipework fittings, ensure the Hoses do not kink or become twisted when tightening.
- Check all fittings and connections are secure and water-tight.
Plumber note
-
On-site testing using higher water pressures must be conducted with the Mixer in the closed position.
(STATIC TEST) -
Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
-
At the completion of testing, do not relieve any high water pressure by operating the Mixer.
-
Exposing the internals of the Mixer Car tridge to higher than specified water pressures will void the manufacturers warranty.
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS
3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is
65 deg.c
Copyright © Sussex Taps.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>