SUSSEX BMOS210RH Wall Bath Mixer Outlet System Installation Guide
- June 12, 2024
- SUSSEX
Table of Contents
SUSSEX BMOS210RH Wall Bath Mixer Outlet System
Product Information
The Suba Wall Bath Mixer Outlet System Dress Kit is a product designed for use in bathrooms. It has a product code of CBM and is available in two options: BMOS160RH with a 160mm outlet and BMOS210RH with a 210mm outlet. The mixer dress kit includes a mixer cartridge lever, handle body, set screw, O-rings, and bath outlet. The product is compliant with AS/NZS 3718:2005 and is licensed under LIC. 20081. The Suba Wall Bath Mixer Outlet System Rough In is another variant of the product with the same product code CBM. It is also available in two options: BMOS160RH with a 160mm outlet and BMOS210RH with a 210mm outlet. The rough-in plumbing kit includes a masterfit, backplate, outlet fitting, outlet, and handle body. The product is compliant with AS/NZS 3718:2005 and is licensed under LIC. 20081.
Product Usage Instructions
Mixer Dress Kit Installation
- Remove the protective cover from the mixer.
- Using silicone, seal the wall surface around the mixer.
- Apply a small amount of silicone to the rear of the backplate before mounting it onto the wall.
- Fit the handle body onto the mixer cartridge lever, ensuring the handle is fully engaged.
- Secure the handle body by tightening the set screw using the provided Allen Key (tighten well).
Outlet Fit Off
- Apply a small amount of grease to the O-rings of the fitting.
- Carefully fit the outlet, ensuring the locating pins align with the backplate.
- Secure the outlet by tightening the set screw.
- To complete the installation, operate the mixer(s) and check the flow of both hot and cold water from the outlet. Check all fittings and fixtures for water leaks.
Rough-In Plumbing
- Prior to installing, calculate the finished wall thickness. If it exceeds 30mm, contact the manufacturer for further options.
- If the wall thickness is greater than 30mm, contact the manufacturer for further options.
- Prepare a nogging to be fixed parallel between the wall studs.
- The nogging must be fitted to enable the base of the masterfit to be 30-32mm back from the stud face.
- The masterfit will be marked “This side UP” to indicate orientation.
- Using the provided screws (x4), mount the masterfit to the nogging, ensuring it is level and square.
Plumber Note: High-pressure line testing should be conducted on-site with the mixer in the closed position (STATIC TEST ONLY). The mixer should not be opened when exceeding the maximum stated water pressure. After testing, do not relieve any high pressure by opening the mixer. Exposing the internals of the mixer cartridge to higher than specified water pressures will void the manufacturer’s warranty.
Important: Tapware installation must be done by a licensed plumber in accordance with AS/NZS 3500:2003. The recommended working water pressure is 300-500 kPa, and the maximum water temperature is 65°C.
For further information and options, please visit sussextaps.com.au.
Product code
- BMOS160RH Wall bath mixer outlet system 160mm outlet
- BMOS210RH Wall bath mixer outlet system 210mm outlet
Mixer dress kit
- Remove Mixer protective cover.
- Using silicon, seal the wall surface around the Mixer.
- Apply a small amount of silicon to the rear of the backplate prior to mounting onto the wall.
- Fit the handle body onto the Mixer Cartridge Lever ensuring the Handle is fully engaged.
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
Outlet fit off
- Apply a small amount of grease to the O-rings of the fitting.
- Carefully fit the Outlet ensuring the locating pins align with the Backplate.
- Secure the Outlet by tightening the Set Screw.
- To complete the installation, operate the Mixer(s) checking the flow of both hot and cold water from Outlet.
- Check all fittings and fixtures for water leaks.
Product code
- BMOS160RH Wall bath mixer outlet system 160mm outlet
- BMOS210RH Wall bath mixer outlet system 210mm outlet
Rough in plumbing
- Prior to installing, calculate the finished wall thickness, maximum is 30mm thick, contact manufacturer for further options.
- If Wall thickness is greater than 30mm, contact manufacturer for further options.
- Prepare a Nogging to be fixed parallel between the Wall Studs.
- The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face.
- The Masterfit will be marked “This side Up” to indicate orientation.
- Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square.
Pipe connections
- The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).
- Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (see Drawing)
- Do not remove any factory fitted pressure plugs or Fixings.
- Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.
- Check all fittings and fixtures for leaks.
- Leave the Mixer(s) in the closed position and replace the Mixer protective cover.
- Store the Dress Kit in a safe place until required (see Dress Finishing Guide)
Plumber note
- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY)
- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
- At the completion of the testing, do not relieve any high pressure by opening the Mixer.
- Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the manufacturer’s warranty.
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003 Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c Copyright © Sussex Taps. sussextaps.com.au.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>