ROCKSOLAR DAFlz8W3fkg DC Solar Water Pump Installation Guide

June 12, 2024
ROCKSOLAR

ROCKSOLAR logo SOLAR WATER PUMP
3LSPS-24-50-1.5-250-1
3LS1S1.3/70-24/250ROCKSOLAR DAFlz8W3fkg DC Solar Water
Pump

DC SOLAR PUMP WITH CONTROLLER

A. Operating principle
Brief introduction of deep well solar pump system

ROCKSOLAR DAFlz8W3fkg DC Solar Water Pump - System

Brief introduction of surface solar pump system

|
---|---

Connection of solar panel Sketch map

Motor Power And Solar Panels Connection

DC Input| DC Pump Voltage VOC(V)| Solar Panels Connect in series
---|---|---
12V 200W| 11-55| | 12V Eatery
Solar panel : I. 50Wp2PCS
24V 1E0/250/300W| 11-55| | 250Wp
1 FC
300TVIPCS
48V 40DW| 45~150| | 250Wp2PCS
300W pt2PCS
72V 600W| 60~150| | 250Wp
3PCS
300W p3PCS
96V 750W| 60~200| | 250W p
r4PCS
300W p9PCS
144V 1100W| 90~340| | 250 p6PCS
300W pe5PCS
192V 1500W| 90~430| | 250W p
8PCS
300W ps7PCS
280V 22COW| 100490| | 250p’ : 2PCS
300Wp4:.OPCS
385V 3000W| 100–750| | 250WpL6PCS
300Wp
L 4PCS

Main Accessory Picture

Instalation

  1. Wiring the pump
    Connecting a longer cable to the pump,(size of cable must be at least 2.5mm*)Use the parts contained in the cable connector kit{heat-shrink tube and tape) to connect a longer supply wire to the pump. If you don’t have a heat gun to shrink the tube, the
    barrel of your soldering iron will do or you can use a butane torch but with great care s0 you don’t melt the insulation or set it on Aire, Bare the insulation back as shown above.

  2. layout the components.

  3. Put the large diameter piece of heat-shrink over the main cable and then the smaller diameter pieces over the individual wires, keep the heat-shrink back away from the joints as you solder them. Any heat transfer will prematurely shrink the heat-shrink.

  4. Slide the small heat-shrink over the soldered joints and heat using a heat gun or alternative heat source to shrink the sleeve down over the wires.

  5. Wrap the tape over the sealed joints

  6. Finally slide the large diameter heat-shrink owner the completed joint and shrink to it.

DOS AND DON’ TS

  • Do keep the Pump into water all the time when operating.
  • Do be careful with wiring.
  • Do remover the pump if Nat used for a long time.
  • Do make sure the pump has adequate water around it during working.
  • Do put your solar PY panels in a sunny position fadngtue north{soother hemisphere) or true south{northern hemisphere). If the panel angle is fixed then an angle equal to your latitude will be a good compromise.
  • Don’t run the pump out of the water, even momentarily.
  • Don’t adjust the regulation belt in the base of the pump. It is factory set. Which damage is not covered by warranty.
  • Don’t use the pump in dirty or corrosive water. Premature wear will not be covered by warranty,
  • Don’t disassemble the pump. There is no user parts inside.

PRODUCT PARAMETERS

Model 3LSIS1.3/70-24/250
Pump Complete S.S. 304 + Screw
Motor Brass Cap + S.S. 304 Body
Controller Inbuilt Controller
Diameter(inch) 3″
Cable 2M
Voltage(V) 24
Power(Wl 250
Max Flow(m3/h) 1.3
Max Head(m) 70
Outlet(inch) 1″
Model 3LSPS-24-50-1.5-250-1
--- ---
Outlet Iron
Pump head Iron
Pump body stainless steel/Iron
Impeller Screw
Motor DC brush motor
Cable 10M
Voltage(V) 24
Power(W) 250
Max Flow(m3/h) 1.5
Max Head(m) 50
Outlet(inch) 1″

ROCKSOLAR logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals