ROCKSOLAR 10A PWM Solar Charge Controller User Manual

June 12, 2024
ROCKSOLAR

ROCKSOLAR 10A PWM Solar Charge Controller User Manual
Solar Charge Controller

SAFETY INSTRUCTIONS

  1. This controller is suitable for 3 types of batteries, including lead-acid bateres (12V/24Y auto. – {on battries( irngs af 111V inium im iron phosphate batteries (4 strings of 12.8V) Don undmmmrnm-ry Battery type description:
    B1
    Is wlea-acia bamery (121724 auto):
    B2 Is a ithium fon battery (3 strings of 11.1V lithium batteries);
    B3 Is ithium iron phosphate batery (4 strings 12.V)

  2. The battery cable should be as short as possible to minimize loss.

  3. When Installation for the first time, set the battery type according to the type of battery and make sure that the battery has enough voltage 0 that the contraller can recognize the correct battery type.

  4. The charge regulator Is only suitable for regulating solar modules. Never connect another charging source to the charge regulator.

PRODUCT FEATURES

  1. Build in industrial micro controller
  2. Big LCD display.all adjustable parameter.
  3. Fully 3-stage PWM charge management ‘
  4. Build-in short-circuit protection,open-circuit protection reverse protection,over-10ad protection.
  5. Dual USB output, the maximum current of 2.54, 10 support Apple’s mobile phone charging.
  6. Dual mosfet Reverse current protection,low heat production.

LCD DISPLAY/KEY

Product Instruction

MENU: Switch between different isplay o to enter/ex]t setting by long press.
Up: presstoincreaae value.
DOWN: Pross to decrease value,

SYSTEM CONNECTION

  1. Connect the battery t the charge regulator plus and minus
  2. Connect the photovoltaic module o the regulator-plus and minus.
  3. Connect the consumer to the charge regulator-plus and minus.

_ The reverse order applies when deinstalling! Animproper sequence order can damage the controller!
Dimension
_

Note: 12V battery with 18V solar panel 24V battery with 36V solar panel

LCD DISPLA /SEETING

Setting

Browsing Interface
Press MENE to browse Different interface

Set Parameter

In interface 2.5 long press MENE to inter setting and using UP and DOWN to set the parameter long press MENE again to exit long press Down to restore parameter.

Attention

  1. Press the [DOWN] button to ON/OF load manully at main display.
  2. The work mode is working as below.

[2H] load output 24 hours
[1-23H] load on after sunset and dosed atfer setting hours
[OH] Duskto dawn

TROUBLE SHOOTING

Situation Probable cause Solution
Charge icon not on when sunny Solar panel opened or reversed Reconnect
Load icon off Mode setting wrong Set again
Battery low Recharge
Load icon slow flashing Over load Reduce load watt
Short circuit prolection Remove short circuit, 1 minutes or so automatic

recovery
Power off| Battery too low/ reverse| Check batterytonnection

TECHNICAL PARAMETER

Batt voltage 12V-24V AUTO
MODEL W88-A
Charge current 10A
Discharge current 10A
Max solar input 1224Vvbbaa iteer;yy. twhteehni glee ti ig2geVi. t

46V
Battery type| BI =Lead acid battery I 2V, 24VautoB2=Lithium-ion battery (lithium battery) 3 strings 3.7V=11.1V B32 Lithium iron phosphate battery 4 strings 3.2V =12.8V
Equalization| 14.4V(B1)           12.6V(B2)           14.6V(83)
Discharge stop| 10.7V(1301)        9V(B2)                10V(B3)
I= PI ?) re%7| 12.6V( 61)          10.5(82)               12V(B3)
Voltage of open light| Solar panel 8V(Light lights delay)
Voltage of close light| Solar panel 8V(Light off delay)
USB output| 2 way USB output. 5V/2.5A(MAX)
Self-consume| <10mA
Operating temperature| -35 •-•••• +60C
Size/Weight| 133.5′ 70′ 35mm      / 130g

  • All red color voltage x2 while using 24V system
  • This instruction is a general manual, such as a slight difference inthe physical
  • Product specifications are subject to change without prior notice

Web: www.rockaniar.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals