Danfoss FHM-CN2 Pre-Aassembled Mixing Shunt Installation Guide
- June 12, 2024
- Danfoss
Table of Contents
ENGINEERING
TOMORROW
FHM-CN2 Pre-Assembled Mixing Shunt
Installation Guide
Installation Guide
FHM-CN2
Pre-assembled Mixing Shunt
Installation overview
Installation
The FHM-CN2 must be connected to a system according to the
illustrations.
| Primary water side (horizontal direction)
---|---
| Secondary water supply
| Secondary return
| Primary water supply (vertical direction)
| Primary return
- Remove the union nuts 1, 2 and 3 and rubber gasket 5 from mixing shunt which to be used in steps below, as shown in Fig. 2.
- Pre-mounted union nut 1 for connection to the primary side supply pipe . The union nut 1 to control valve 4 must be tightened with a torque of at least 85 Nm without any sealing materials, as shown in Fig. 2.
- Pre-mounted union nuts 2 and 3 for connection to the secondary side pipe or directly on a Danfoss manifold. The union nuts 2 and 3 to mixing shunt must be tightened with a torque of 15 to 25 Nm with enclosed rubber gasket, as shown in Fig. 2.
- The end of primary side return pipe E1 for connection to primary side return pipe E.
- Remove the blue cap 6, as shown in Fig. 2.
- FTC thermostatic sensor is in package. Mount it on the valve according to the enclosed instruction, as shown in Fig. 3.
Optional Installation Type
Refer to Fig. 2, Fig. 4, Fig. 5, Fig. 6 structure, can choose to install the
manifold in the mixing shunt left.
Tips Connection 7, 8 and 9 are tightened from the factory. Please double check them during installation. If loosening or leaks occur due to transportation or moving, please tighten:
- Connection 8 at a torque of 15 to 25 Nm.
- Connection 4 and 7 at a torque of min. 85 Nm.
- Connection 9,7 and 10 at a torque of 30 to 40 Nm
Adjust bypass control valve AVDO to required different pressure according to actual application, as shown in Fig. 7.
RoHS compliance
| Part Name | Hazardous Substances Table |
|---|---|
| Pb | Hg |
| Pump | X |
| Brass parts | X |
O: Indicates that this hazardous substance contained in all of the homogeneous
material for this part is below the limit requirement in GB/T 26572.
X: Indicates that this hazardous substance contained in at least one of the
homogeneous material for this part is above the limit requirement in GB/T
26572.
Danfoss/S
Climate Solutions • danfoss.com • +45 7488 2222
Any information, including, but not limited to information on selection of
product, its application or use, product design, weight, dimensions, capacity
or any other technical data in product manuals, catalogues descriptions,
advertisements, etc. and whether made available in writing, orally,
electronically, on line or via download, shall be considered informative, and
is only binding if and to the extent, explicit reference is made in a
quotation or order confirmation. Danfoss cannot accept any responsibility for
possible errors in catalogues, brochures, videos and other material.
Danfoss reserves the right to alter its products without notice. This also
applies to products ordered but not delivered provided that such alterations
can be made without changes to form, fit or function of the product.
All trademarks in this material are property of Danfoss A/S or Danfoss group
companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/5. All
rights reserved. 
© Danfoss | Hydronics | Sub-Systems | 2023.08
AN45665682284301-CN0102
Documents / Resources
|
Danfoss FHM-CN2 Pre-Aassembled Mixing
Shunt
[pdf] Installation Guide
AN45665682284301-CN0102, FHM-CN2 Pre-Aassembled Mixing Shunt, FHM-CN2, Pre-
Aassembled Mixing Shunt, Mixing Shunt
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>